To determine what size of fixture is going to fit best in a foyer add the room dimensions together. For example, if your foyer is 12' by 18,' add 12 + 18 =30. The size of fixture for this foyer would be 30" in diameter.

When choosing a fixture for the dining room is to have the diameter equal to 1/2 the width of the table. For example, if the width of your table is 52," select a chandelier that has a diameter of 26." The fixture should hang so the bottom of the fixture is approximately 30" above the tabletop.

A chandelier should be chosen based on the width of the foyer, the ceiling height and any architectural details, such as double doors, or a window above the door. A general rule is the chandelier width should be at least the same size in inches as the diagonal measurement of the room in feet.

To determine what size of a chandelier would fit best in a foyer-or any room-simply add the room dimensions together. For example, if your foyer is 12' by 16,' add 12 + 16 = 28. The proper size chandelier for this foyer would be 28" in diameter.

Hip size is the best guide for proper fitting. The SAFEHIP® sizing chart identifies which product to order based on the hip size.

On every product detail page you will have the option to view the size chart for the designer of the dress you are ordering. Keep in mind that over 90% of special occasion dresses need alterations. We are not responsible for dresses that do not fit, those size charts are direct from the manufacturers and they cut their dresses according to those size measurements.

Response: To determine what size of a chandelier would fit best in a foyer, or any room, simply add the room dimensions together. For example: if your foyer is 12' x 16', add 12 + 16 = 28. The proper size chandelier for this foyer would be 28" in diameter.

That is our responsibility. You just supply us with your height, weight, and actual waist size. We've been fitting athletes for over 10 years. We've picked up a little bit of knowledge along the way. We know how important the fit is to your success.

Usually using the same size and type bulb that came with the lamp is the best thing to do. If you are talking about the 220V (tube type) bulbs, then it would depend on the way the fixture is built. For instance, if you have a fixture where the bulb is completely covered, putting a larger wattage type bulb in can cause not only the bulb to burn prematurely, but can cause the whole fixture to burn up.

The Moss & Glance fixtures require a hole of 4" (100mm) and a minimum depth of 2" (50mm). The Illusion & Mistral fixtures require a hole of 5.5" (140mm) and a minimum depth of 2.5" (65mm).

For ground positioning, you will need an area of open space of about 10" x 5" to accommodate the light thereby allowing a little space all round the fixture.

Determining the correct size genset for your boat is not a difficult task, however it should be done by an experienced and knowledgeable marine electrician. The American Boat & Yacht Council's manual of standards, section E-8.18 provides guidelines to determine how much power you need. We recommend these guidelines are followed. For more information about ABYC and details on generator sizing, go to

We highly recommend, regardless of your weight, height or physical body condition, you measure your arm circumference. If your arm size is 7 to 9 inches you need the small adult cuff, 9 to 13 inches is the standard size adult cuff, and 13 to 17 inches is the large adult cuff. Each model is approved for use with specified cuff sizes. When the wrong cuff size is used you may get an inaccurate reading at your first measurement, or after a short period of use because the cuff bladder is damaged.

The filter shipped with your Carrier unit is made from higher-quality materials than those of the disposable filters found in retail stores. For that reason, replacement Carrier filters can only be purchased through a Carrier dealer. However, keep in mind that Carrier filters are reusable, and can be washed by hand in cold water. Your Carrier dealer is your troubleshooting expert, and is glad to help you.

Measuring for a bracelet - Use a soft tape measure and give me the measurement of your wrist, at the wrist bone, not the bracelet size you usually wear. Note the measurement to the closest 1/4 of an inch or in centimeters and enter it in the "comments" section when checking out. (If you do not have a soft tape measure, use a string and then measure that using a ruler.) Sometimes if a bracelet or bangle needs to made unusually large, there may be a price adjustment.