In Most cases a broken heater control knob adjuster can be attributed to binding heater control box. The repair is to either reposition the control box with additional clips in a manner that will free up the box from binding or to completely replace the heater box. Most of the problems with heaters not working correctly can be attributed to faulty thermostats. The problem is typically an issue with the thermostat being stuck open.

Yes, if you hold the "AC" button for three seconds, you can control both zones with the driver's side temperature knob.

Originally, the Drag control was supposed to be recessed so that once set, the control would not be touched. However we found that it was so darn musical that people would be adjusting it all the time. Because the JDV will probably live on the floor most of the time, we felt that a knob would stick out and get kicked and broken. So no knob. Kinda' looks weird at first, but you'll get used to it.

Our patent-pending One Knob control is specially designed and programmed, so that all you need to adjust the Turns Per Day is one simple turn of the front knob, then the required TPD is set! No complicate operation is required. So advance yet so simple to use. Anyone could set the Techwinder's Turn per Day in one simple turn, to fit your watch's unique winding requirements.

The red knob is there simply to remind you when to replace the activated carbon granulate. When the carbon has been used for 6 months, it needs to be replaced. The red knob can be turned (with the help of a coin) to the appropriate month, to make it easier to remember.

Yes. The peripheral controller is interchangeable between rat and mouse hardware. So for example you could be acclimating 32 rats while monitoring 32 mice with the peripheral controllers.

Parts may distort as they solidify and cool in the die, or during ejection from the die. These problems are solvable but usually require discussions between the part designer, the tool designer and the die-casting engineer since they involve increasing draft angles etc. However, part distortion is quite often caused by mishandling during press trimming, polishing etc. or when the parts are clamped in jigs for machining, plating or painting.

It's no problem to add either a volume or volume and tone control to these pickups. Simply install them in line after the preamp. You should use the same 25K audio taper pots that are used with our electric pickups. These are generally available from your EMG dealer, or can be purchased directly from the factory.

The Tone control delivers a wide spectrum of midrange and bass timbres. You can dial in everything from an extremely scooped to raucous, bluesy midrange voicings.

Sure. We have chromium-plated solid brass knobs in a variety of styles, or plastic knobs. Our plastic knobs all have a metal core that provides a solid connection to the spindle of the switch. You will need to consider shaft size, threads (if any) and symbol or text. Check the online catalog under Accessories/Hardware/Knobs. If you have a Master Catalog, see section Q. Use our M-630 Push-Pull Switch. It's an On-On switch.

Well, to get a little more complicated, distortion is any departure from a true and accurate reproduction of the original waveform. It can include Noise, Clipping Distortion, Harmonic, and Intermodulation Distortion. These last two forms are fairly common in loudspeaker reproduction and can be reduced but not entirely eliminated in the existing technology.

Answer - It is possible to use distortion on a semi acoustic guitar but you will likely have feedback because the guitar is hollow. Stuffing foam rubber in the sound holes will lessen the feedback.

ANSWER: This is an "Address Switch" that sets the ID number (board address) of the Light Controller in question. Other items on the Light Controller are detailed in the Hardware Wiring Information file in the "Technical Support" section of our website.

No, but there are numerous colour varieties that have been developed such as hooded, capped, self, mink, rex etc. Details of the various varieties can be found all over the web, including the National Fancy Rat Society website (www.nfrs.org).

Reason 1: Distortion causes the power spectrum to shift upwards in frequency. A bass note, when distorted, will have lots of high frequency energy. This will cause mid-ranges and tweeters to fry, if the amplifier is operating full range. It doesn't harm woofers, necessarily. Reason 2: Distortion causes the average power to be much higher. Typically, a music signal that never clips has an average power level of 1/4 the peak power level for even the most compressed speed metal or pop.

For linear distortion I measure the dB magnitude deviation of the frequency response from my performance target that I have set for on-axis and off-axis response of the speaker, utilizing the data that you can see on the System Test page. I measure phase response for summation of driver outputs in the crossover region. In the time domain I look at stored energy using shaped tone-bursts (FAQ17) to characterize drivers and cabinets.

In brief, rat owners bring their rats to be seen by the public. Rats are shown in suitable tanks. During the day, the judges choose the best rats and award prizes. Rat shows are also social occasions where friendly rat owners share their common interest. Many shows will have a variety of other activities taking place – these are usually listed on the show calendar.

NFP (Natural Family Planning) is different from artificial birth control in many ways: NFP is healthy. All artificial birth control methods have possible side effects, some of which can be quite serious. Natural Family Planning has no side effects, and is a healthy non-invasive choice for family planning. Some artificial methods (particularly hormonal methods [pill, patch, etc.], the IUD, and sterilization) can have long-term impacts for the future fertility of the couple.

Access rights are controlled by issuing passwords. Journalists, for example, can thus be given access to different pictures than employees.

The past couple of years have seen the improvement of birth control options. There are new, lower dose pills with less side effects than just a few years ago. There is also the birth control shot (Depo-Provera) that you get at the office every 3 months. No appointment is required for each shot. It has only a 1% failure rate. There is also the birth control patch. It is a patch that goes on the skin once a week. It's side effects are similar to the pill.