The electronic controller is programmed to know the water softener’s capacity. It uses the softener capacity, the hardness setting and the water usage from the meter to continuously adjust to the customer’s water using habits. The electronic controller is searching for a water usage pattern and may seem to regenerate more frequently or not enough for the first few weeks of installation.

Depends on your water usage and hardness level. In a typical household it will regenerate every 2-7 days.

No, this unit regenerates with just a 1 pound box of table salt. You just shut off the water supply, unhook the outlet side of the water softener, twist off the tank cap, pour in the table salt, put the cap back on, turn on the water supply, and rinse the unit for about 15 minutes. This will complete the regeneration process.

Normal regeneration time is 2 hours. It normally takes place at night time (2:00AM0 when water usage is at a minimum. For a model S100ME (30,000-grain model) 30 gallons of water & 6 lbs of salt are used per regeneration at factory setting.

About 2 hours. Generally water softeners come preprogrammed to regenerate at 2:00 a.m., however can be reprogrammed to regenerate at any desired time. No. Water softener discharge water should not affect septic system operation or drain field soil percolation.

Our standard installation is quick and unobtrusive. Once installed, you can forget about it except for adding salt as required. In most cases our standard domestic installation method is suitable for most households. If there are any difficulties we can advise you about this when we carry out the survey. But rest assured ... we usually have a way to get round any problems.

The most common water softening method is called "ion exchange.” Put simply, this type of softening is a process where calcium and magnesium (the minerals that make water hard) ions are exchanged for sodium ions. This exchange takes place in a "resin bed" made up of a tiny bead-like material. The beads have a negative charge and attract and hold positively charged ions such as sodium.

A water softener removes calcium, magnesium, lime, and iron from supply water. By removing these minerals, you eliminate buildup in pipes, on fixtures, and in your RV water heater.

Answer: : The particles do not go anywhere. All of the particles and chemical elements in the water before the Sterling Water Conditioner will still be there after the water passes through the Sterling Water Conditioner. The only difference is the increase in Zeta Potential and its consequent impact upon the crystallization properties of the minerals in the water that cause scaling and hard water spots.

Water softeners work on the principle of "ion exchange". "Ions" are electircally charged atoms or groups of atoms. Tiny beads of plastic (called resin) inside a water softener mineral tank are surrounded by ions of sodium or potassium which have a weak magnetic attraction to the resin. Calcium and/or magnesium ions (hardness) have a stronger magnetic attraction to the resin than the sodium or potassium.

EcoWater softeners have an electronic display to show when to top up salt - just like your dishwasher. If access is restricted, a remote monitor is available.

Appliance Tip of the Day: No Ice in Your Whirlpool or KitchenAid Side-by-Side Fridge with In-Door Ice Frigidaire 30" Free-Standing Ranges with Mini-Oven: Beeping Sound from Control Panel but No Fault Code

The amount of salt placed into the brine storage tank has nothing to do with the amount of salt used during the regeneration cycle. Water will dissolve and absorb salt only until it becomes saturated. A given amount of brine (salt saturated water) contains a specific amount of salt. Just make sure that there is at least enough salt for a regeneration cycle (12 lbs. in the case of our unit). Most homes are plumbed with ?" copper pipe (in larger custom homes might be 1").

It all depends on the hardness of the raw water. The following table shows the additional amount of sodium consumed by drinking one quart of softened water.

A water softener simply exchanges hardness ions (calcium and magnesium) with sodium ions. This process is called ion exchange. This exchange takes place within the media (resin) tank. When water flow through the tank it comes in contact with small resin beads that are covered with sodium ions. As the water flows by the sodium ions they are exchanged with hardness ions. Eventually the beads contain nothing but calcium and magnesium and no sodium.

No. Generally, water softeners can use either. With potassium chloride, you will use more material than with salt. Is it true that salt kills bacteria? I do not want the level of "good" bacteria in my septic system to be affected. VERY high concentrations of salt can kill some bacteria. However, the concentration of salt that is used in a softener is NEVER high enough to kill bacteria in septic systems.