Plywood, MDF (medium density fiberboard), and Hardboard ? If measured floor-to-ceiling height is 8' or less, subtract 1/2" from the measurement to allow 1/4" expansion clearance top and bottom. Transfer these measurements to panels for cutting. If using a handsaw or table saw, mark and cut the panels face up. If using a portable circular saw or saber saw, mark and cut panels face down.

Georgia-Pacific Plywood, Hardboard, and MDF (medium density fiberboard) ? Panel grooves are usually located every 16", allowing nails to be placed in the grooves on standard 16" stud centers. Panel matching colored ringshank nails are recommended. Use 1" nails to apply paneling to studs alone, 1-1/2" nails to apply paneling through a solid backing or plaster. Space nails 6" along panel edges and 8", (12" plywood) on intermediate studs. Please wear eye protection when nailing.

Endurance® can be cut with most saw types. When using a power miter saw, a high tooth count (80 or more) carbide tip is best. Be sure to have the blade up to speed before beginning your cut. Hack saws and other saw types with metal cutting blades will do the job.

Solexx panels can be cut with a simple utility knife. Because the material is so flexible, it’s also possible to bend it around many curves and corners on a structure.

Adhesive application may be used to apply Plywood, Hardboard and 1/4" MDF.* For 5/32" and 1/8" MDF use both adhesive and nails. Plywood, Hardboard and MDF ? adhesive may be used to apply panels directly to studs or over existing walls as long as the surface is level, sound and clean. Once the panel is fitted, apply beads of adhesive with a caulking gun in a continuous strip along the top, bottom and both sides of the panel. On intermediate studs, apply beads 3" long and 6" apart.

All Georgia-Pacific decorative wall panels can be installed in dry basements following installation recommendations installation instructions for below grade and over masonry walls. Please see installation instructions (PDF: 273KB/8pgs) for more details.

To remove surface accumulations such as dust, just wipe Georgia-Pacific decorative panels with a soft cloth dampened with furniture polish containing no waxes or silicones. More stubborn accumulations may require wiping with a soft cloth dampened with a solution of lukewarm water and a mild liquid detergent. Wipe with a clean, dry cloth immediately following this procedure.

Georgia-Pacific Prefinished Decorative Panels are manufactured with a beveled edge coated the same base color as the groove lines so seams need not be finished. If desired, the appearance of seams can be minimized by painting the backing behind the paneling in the seam area a matching groove color to reduce any contrast at gaps left for spacing due to slight dimensional changes.

Nu-Zymes? should be taken just before or during meals, especially every cooked meal, for help with stomach related symptoms like gas, heartburn, acid reflux, water retention, bloating, fatigue, etc. Depending on your body weight and the size of your meal, you should take 2-6 capsules. For example: A person weighing 150 pounds who has a hamburger, French fries and a soft drink should take 2-3 capsules.

The Ventmaster can cut through wood framing, sheet metal, asphalt shingles, and green wood. It is even effective on metal roll up doors commonly found on industrial warehouses. It can also cut through car bodies, hoods, and windshields. Yes. Contact Tempest Customer Service at 800-346-2143 for more information on the Ventmaster 375-K rotary cutoff saw.

No. It is not recommended to use a circular saw to cut pavers. A brick splitter or a high-powered saw with a diamond blade is recommended. These are readily available to rent at Michigan Skid Loader (www.mslinc.com) or other equipment rental stores. For a few cuts, we can cut them for you for a small charge.

Not yet, but we are working on it. Our system will be able to measure 8 feet to the left and 8 feet to the right.

First, why would any plant be used only for decorative use? The flowers I buy, or grow, are potted and living. I sometimes do buy cut flowers, but they never go to waste. When they are done blooming I save the petals and leaves and dry them for use in spells, potpourri, etc. In the end, as long as nothing ultimately goes to waste, it's okay to pick flowers for decoration. Whatever you do, always remember to honour that which has given itself for your use (just like herbs, fruits, etc.

For an in-depth discussion on this, see A Perspective on Lighting. In general, they produce a more desirable environment when used in Offices, Office Cubicles, Health Clubs, Dental or Chiropractor offices, or even college Dorm Rooms,. There are countless other lighting installations and businesses that would enjoy the decorative enhancement produced by our Fluorescent Lightshades™.

Touch panels are available in digital and analog types. There are three types of analog touch panels: Resistive, capacitive and acoustic.

For equipment positioned close to a wall surface, place as much square footage as practical with a preferred coverage of 32 sq. ft. The HSS4 Sound Absorption Panels are recommended as they come in several sizes and are impervious to dust. See Product description. Equipment sitting towards the center of the room (table saws, jointers, planers etc.) require sound absorption panels to be placed on the ceiling directly over the equipment if possible.

Lionite? Tileboard and plank paneling products can be used within mobile homes. These decorative panels are certified to meet HUD 24 CFR Part 3200 formaldehyde emission requirements for plywood wall paneling and can be used in mobile homes with adequate ventilation. Our other decorative wall panels contain low levels of urea formaldehyde resin and may release formaldehyde vapors in extremely low concentrations.

Building codes require that panels thinner than 1/4" be installed over a non-combustible backer over studs. Georgia-Pacific Western Vista panels, 1/8" and 3/16" hardboard; 1/8" and 5/32" Mount Vernon? and StyleLine? wall panels always should be installed over a solid, non-combustible backing such as gypsum wallboard. Please see installation instructions (PDF: 273KB/8pgs) for more detail.

Georgia-Pacific manufactures several different types of decorative panels. Prefinished Georgia-Pacific decorative panels should not be painted. These panels are ready to use and need no additional finishings. Jubilee? Ready-to-Paint is factory primed and intended to be painted as needed with a high quality acrylic latex paint. Any of the unfinished real wood decorative panels from Georgia-Pacific are paintable.