Our mantels are available in two finishes: a smooth finish and a distressed finish. Our standard smooth finish is like fine honed limestone. (Not shiny like polished granite.) To achieve this finish, we wet sand or lightly acid etch the material after removing it from the mold. Our distressed finish, achieved by sandblasting, has a rougher surface texture and presents an older or more rustic appearance.

This question usually initiates a lively debate between rough and smooth collie owners! The answer is yes, there is "some" difference. Generally speaking, the smooth collie tends to be a bit more active than the rough. (Granted, any of us would be more active if we were running about in our underwear instead of wearing a big fur coat!) Nevertheless, both varieties are equally gentle, intelligent and affectionate.

It is customary to always paint on the smooth side of the paper. However, if you cannot tell the difference, then do not worry about the difference.

All milled papers are smooth and flat with only a slight texture. Handmade papers can be made either smooth or rough. When handmade paper is formed on the mould it has random ridges running throughout the exposed side. These we describe as 'satisfyingly nobly' and give the paper a heavy texture. To obtain smooth handmade paper these ridges are flattened out using a simple handheld tool.

The smoothness of the surface has a major influence on the air requirements. The rougher the surface, the more air will be required to maintain the air film. On a rough, sandpaper-type surface increased friction can cause more wear on the air bearing material.

Slightly textured - similar to the texture to that is embossed into the vinyl top of a car. . We often say that the panels mimic the look and feel of a refrigerator door (the texture is a little different, but this is a great analogy). The light pebble grain texture pattern is embossed into the aluminum sheets (there is no vinyl whatsoever on this cover!).

Almost all rapid prototyping materials can have surface finish and cosmetic improvements made to them. Both SLS and SLA can be sanded, filled and painted to look like injection-molded plastic. Surface texturing can even be applied if time and budget allows. Most parts, however, do not require high level finishing, and are simply sanded and bead blasted. This creates and nice surface finish that is excellent for engineering purposes.

If you have a textured wall, a wood-paneled wall, a brick or concrete wall, or any other rough surface, we recommend the installation of a "liner paper," followed by 2 coats of flat latex paint. A liner paper is simply a blank wallpaper which covers irregularities in the wall surface.

The powder coated surface of the cover is a smooth powder coated satin black finish. The top to the canister is slightly textured ABS plastic that is similar in texture to that is embossed into the vinyl top of a car (or virtually identical to a soft vinyl cover.

After mixing and applying to the surface to be repaired, using a putty knife or rubber gloves that have been dipped in water, rub on the surface and you will form a very smooth surface. Make sure you clean your mixing and shaping tools as A + B? Epoxy Putties and Pastes will cure on metals and plastics.

Use a penetrating sealer that will allow an additional coat of a gloss sealer. See our Installation Specification Guide for details.

We offer a rugged texture to resist scratches from normal wear and tear. It is our goal that our product lasts and looks good for years on your vehicle.

No. Many natural stone slabs contain pits and fissures that are natural characteristics of stone. Some types of stone exhibit these characteristics more than others, and the lighting of the room can make these marks more or less visible. Ask the professionals at Majesty Marble and Granite, Inc. about the characteristics of the material you are considering for your project. The 2 cm thick stone is approximately 3/4" thick, ranging from 5/8" to 7/8" in thickness.

Western Red Cedar is sold in a variety of patterns and grades, and the texture will be either rough (rustic) or smooth. Rough textured wood surfaces will absorb and hold more finish. The rough side is recommended in most cases. Smooth textured wood surfaces are less absorbent and more difficult to build a surface "film" upon. For this reason, a minimum of two coats of a film-building finish are recommended for smooth sidings to be exposed outdoors.

If your exercise mat has a rough side and a smooth side, use it with the rough side up for better traction as you work out.

When the engine warms up, check the exhaust, preferably while driving behind the car. Blue smoke indicates a weak engine while black indicates excessive unburnt fuel. Ideally, there should be no smoke. Ask for the Pollution under Control Certificate. Stop the car and open the bonnet. Remove the oil filler cap with the engine at idling speed. The presence of smoke is an indication of serious trouble. While you are at it, remember that the tortoise won the race. Never ever be in a hurry.

MiraTEC is reversible. One side features a rough-sawn cedar-like texture and the other has a smooth surface.

All anatomic (a.k.a. teardrop) shaped implants are textured, as the texturing increases friction and helps keep them from rotating. Since a teardrop implant is different at the bottom than the top, it is important that it maintains its position. Back

In 4 foot (trough to crest) very steep waves as long as you have wind, she’ll reach and run with very little roll. (If anyone starts to turn a little green, get them out of the cabin, eyes focused on horizon, and don’t read, it should pass in a few minutes, if not gone too far). Close-hauled in 4 foot waves some spray will reach the cockpit but you can duck behind the raised pop-top (with dodger installed) to stay dry.