Assembling a Solexx Greenhouse is takes just a few readily available tools. You will need a screwdriver, variable speed drill, sharp knife or utility knife, tape measure, step ladder, GE Silicon-2 caulk, caulking gun, clear PVC glue and a level. I am interested in your Solexx polycarbonate covering. How do you install it? Our specially formulated Solexx greenhouse panels are actually a polyethylene blend.

You will need a size 2 cross head screwdriver for assembly. A mallet may also be useful to help push bungs home. Any allen keys, nuts and bolts required are supplied with your product. back to top

You will need the following common tools to assemble any of our beds: a hammer, a Phillips screwdriver or power drill with Phillips bit (preferred), and a socket wrench with a 7/16" socket.

We provide a hardware pack in all of our units that include all the necessary tools to assemble the product.

Assembly is only required for our beds. All our beds are supplied disassembled to minimize shipping costs. Each bed will come with written assembly instructions and a list of the tools (usually just a hammer and a 3/8 inch socket spanner for the Round Hill bed) required for assembly. Each part is numbered. Bamboo dowels are included to pin the joints together.

All Bell'O? products include complete assembly instructions, and include all fasteners and tools needed. Average do-it-yourself skill is all that is required.

No tools are required to assemble the raised beds. However, to set the pins flush with the top of the planter, a hammer (or nearby rock) may be needed in order to pound the pins into very hard ground. More often, though, the pins can be pushed flush by hand, or left exposed a few inches for use with a shade cloth or greenhouse covering (see below).

Most of the products come KD (knocked down) and can easily be put together in 15-30 minutes, depending on the item. If the customer wants us to assemble the product for them, it is typically an extra 10% added to the cost of the item.

NONE. No tools needed . We have designed our garage screen for simple installation. No long complicated instructions. It is easy as 1,2,3 GUARANTEED! No problem. Our screens were carefully designed to accommodate most standard door sizes. We designed our screens to be flexible enough to fit openings that may be a few inches shorter or narrower.

No. All the favors come just as they are shown with instructions and ribbon or raffia fully assembled. No assembly is required, and they are ready to give to your guests.

All you need is three tools to assemble you loft bed: 1) Ratchet wrench with ½ inch (13mm) socket. 2) Standard Phillips head screwdriver. 3) Rubber mallet (preferred) or hammer. A power drill/electric screwdriver with a Phillips

A good quality Carbide Tipped Triple Chip saw blade is preferred when cutting Plexiglas. This reduces the amount of chipout on the opposite side of the material and produces a smooth edge. A Router can be used to cut Plexiglas as well. The Router should be at least 1.5 HP or better and with changeable collets for a 0.5" Shank quality 2 flute Carbide bit. This reduces the vibration and chattering when cutting and will produce a more smooth edge.

Most of our products are shipped to you fully assembled. If there is significant savings to you on a particular product by shipping in pre-assembled sections, we will send an instruction sheet. In those cases, assembly can be completed in less than 30 minutes, using one enclosed screwdriver.

No, all of the cabinets come assembled and finished. (*Only the cue rack requires connecting the top and bottom sections together prior to installation) Total installation can be completed in less than a hour.

Yes, all our bikes require minimal assembly, you don’t need mechanical experience. For most of our models, you simply need to put on the front wheel, handlebars, brake pads, suspension, wing mirrors and connect the battery. We supply the tools you need.

No. We know you want whatever you choose from us to stand out. Assemble-it-yourself furniture and decor just don't do that. No spending your time surrounded by pieces that you hope will someday look like what you ordered from us Just remove your order from its shipping box and it's ready to go wherever it will make the most impact in your home.

The table is fully assembled before shipping. You only need to follow the easy instructions to fit the table to your machine. We're always available should you have any questions.