Yes, the OneTouch USB Cable can be used with a hub, rather than connected directly into a port on the computer. With the 9-pin serial cable, just plug it into your meter and the serial port (COM port) of your computer. You may need to restart your computer if another device had been using the serial port. With the OneTouch USB Cable, you must install a software driver before using it for the first time.

The light does not come on when the card reader is plugged into the computer. It will only come on when a memory card is inserted into the reader.

No, the USB port will support only one user. If you need to support multiple computers you need to use the Ethernet port and a hub/switch.

A USB hub typically consists of a single upstream port (designed to connect directly to your computer or to another hub) and multiple downstream ports. D-Link provides both 4-port (DSB-H4) and 7-port (DSB-7) models. It allows you to expand the number of devices you can attach to your computer.

Good question. According to the USB spec, software is required to connect not only to first tier devices, but also to any plugged into USB hubs. It appears that there is a bug in the Kodak Mounter and USB connection software causing it to fail unless the camera is "device #0", connected directly to the computer.

No. The Hitch will recognize the hub connect to the first device it finds on the USB hub. If that device is unplugged from the hub, the Hitch will then search for another device connected to that hub, but will never connect to more than two devices at once. No. The Hitch is a bridge device, and contains no memory. This is an advantage because it cannot have any issues with storage, such as hard-disk failures or memory allocation errors. No.

Yes, the CB-USB4 cable that comes packaged with the camera is required to connect the camera to the computer. The stock number for a replacement cable is 200 776. It can be purchased through the Olympus Emporium or 1-800-201-7766.

If the distance between USB slots of your PC/notebook is too far for USB Y-cable to connect, you can only connect prime head of USB Y-cable, as indicated below, to one USB slot of your PC/notebook; and then connect the other USB slot of your PC/notebook with DC-inlet cable's USB head to supply power. Therefore, the power supply head of USB Y-cable is useless.

Yes, as long as the hub uses an external power supply. We do not recommend or support this configuration. Before requesting help from Technical Support, please try connecting the device directly to the computer's USB port.

Please make sure the USB cable is made by Fortuna, and please download USB driver and firmware upgrade instruction from GPSmart download page for you to install the USB cable.

Yes, you can connect the player directly to your computer using an Ethernet crossover cable. You can purchase a crossover cable at most retail computer stores. Once you have this connection, you'll need to set up your network adaptor and Squeezebox with static IP addresses so that they can find each other.

A hub is a network device that extends the network so that you could connect more than one computer to the network jack. A network hub can be borrowed from the ITS department. Verify if your hub has a button called Normal/uplink near the rightmost end. It is not necessary that your hub should have the Normal/uplink button. If you see the button, make sure you press the button inwards to set it to uplink.

Yes- The phone should work properly when plugged into a USB hub. If experiencing problems with a vPhone using a USB hub, plug the vPhone directly into the computers USB port.

The maximum length for a USB cable is 5 meters (197 inches). The power transferred through a USB cable that is greater than 5 meters in length will start to decrease, and the device may not function properly.

Yes. SELECT customers may have up to four computers connected simultaneously. However, CLASSIC customers may only have one computer connected to the network at a time. Yes, with Choice OnLine you can surf the Net and simultaneously make phone calls or watch TV. To use a fax machine or dial-up modem while surfing the Net, you must have a normal phone line available. Your computer will not allow you to use our Choice OnLine service and dial-up to another Internet service simultaneously.

A USB cable and the presence of USB connections are not yet adequate for exchanging data successfully. However, data transfer can be effected using a USB cable if a serial COM Port is emulated by the GPS receiver. The GPS data must be available in the NMEA 0183 format when data is called up online, so that Geogrid is in a position to evaluate these data.

We aren't planning our own USB interface, because it involves a lot of low-level machine- and OS-specific driver work. This is best done by companies in the business of doing this—i.e., the ones selling USB-serial adapters. We continue to recommend the Keyspan USB PDA Adapter as the best solution for Macintosh, Windows, and Linux platforms.

With the exception of the HT82K68A/E, the USB interface associated registers for the HT82XX Keyboard/Mouse/Joystick MCU series devices, are placed in Bank0 RAM at addresses 1AH~1CH (USC, USR and SCC registers) and Bank1 RAM at addresses 41H~4BH (Pipe_ctrl, AWR, STALL, PIPE, SIES, MISC and FIFO0~FIFO3). There are some small differences in the Bank1 RAM internal Registers for different part numbers. For more details on the specification please consult the Holtek Data Sheet.

You'll need to use the CubeSat Kit USB drivers. You can use the USB port as a simple terminal interface to the Flight MCU, or you can write your own software in the Flight MCU and/or the host side to do things like serial bootloaders, etc. Physical packaging issues dictate that a user module can connect to the PC/104 bus, and to either the PC/104-Plus bus or the CubeSat System Bus, but not both.