No. Using instrument cable to hook up your speakers can cause intermittent power loss, cause your amp to oscillate and damage the amp and/or your speakers. Please use 18 gauge cable or heavier (16, 14, or 12).

It is relatively easy to connect a HSU subwoofer to certain computer sound cards. These sound cards have a dedicated subwoofer output. Without a subwoofer output on the card, it is still possible to hook up a VTF or STF-3 subwoofer, since these subwoofers have stereo inputs. Use a Radio Shack splitter/adapter (one 1/8-inch stereo male to two 1/8-inch stereo female). Take the stereo 1/8-inch output from the computer sound card.

No. The JDV is not a load box. This means that you must connect the amp to a load 1st (like a speaker) and then you can connect the JDV to the load.

No. Using instrument cables to connect your speakers can result in intermittent power loss, amp oscillation and speaker damage, as well as rendering the cables useless for any purpose. We recommend using 18-gauge or heavier speaker cables.

The audio output is a standard line-out 3.5mm stereo jack, with an AC voltage of 1-2V. This can connected directly to the auxiliary input of most HIFI amplifiers, in place of a CD player. There are also four solder points on the PCB for 'hard wiring' audio. See the manual for more details. Another useful gadget is an FM stereo transmitter, which can be used to broadcast the audio output from the player to nearby radios and/or HIFI receivers.

I just removed one yesterday from the junk yard. It's the same procedure Matt D listed below. Just remove the the rear seat enough to lift the rear deck lid up around the speakers. There are three clips and three 8 mm bolts. I removed all three bolts and two clips. Then I went to the trunk and carefully pulled the speaker and amp assembly down. If you simply need to remove the speaker, that is even easier and can be done solely from the trunk. - /Bryan (91 SE), 6/16/01.

If the speaker are rated for 400 watts peak and are 8 ohms, then you can use an amp that is 400 watts (peak) per channel @ 8 ohms (an 800 watt amp). You can use a lower wattage amp, but you will be limited by the amp. You can also technically use a higher wattage amp, just don't use it a higher volumes which would drive the speaker over its wattage limit and potentially blow the speakers.

This can be a long answer, but to keep it simple; each speaker has a load resistance usually given in ohms. When you add speakers in parallel, jumping one to another, it lowers the ohms by half (i.e. - adding two 8 ohms speakers is a 4 ohm load on the amp). So back to the question; if in the amplifier specs it gives you the wattage for a certain load (Ohms), it is safe to run the amp at that level per channel.

Each speaker is uniquely designed, timbre matched, and seamlessly coordinated in its own system; in order to ensure the most impressive sonic attribute and true cinema experience, we strongly encourage you to mix & match only in the same series of speakers. If your order includes 5 speakers, and one subwoofer, you are entitled to receive a set discount.

On the rear of every amplifier there are either one or multiple output jacks. The outputs vary by model, but typically will be in the form of RCA, Speakon, Balanced XLR, and Banana binding post. Simply choose the output type on your amplifier and connect it to the input on your speaker.

The sound quality QChord delivers through its built-in mono speaker and bass port system is impressive. But you'll be truly amazed when you hear it in stereo. To connect to your own stereo system, you need a QChord Stereo Cable. Note that you are supposed to connect to your stereo amplifier, not directly to the stereo speakers.

Yes, the jukebox has a headphone jack on the back panel. Inserting a plug in this jack will turn of the built in speakers. You can find a a pair of suitable external speakers for the jukebox in our online store by clicking here. Most powered speakers designed for a PC should work OK. quot;Setup cannot continue because some system files are out of date on your system. Click OK if you would like setup to update these files for you now.

You can use amplifiers made by other makers, but the transitional characteristics of ECLIPSE system components, including the amplifier, are all optimised to faithfully reproduce the characteristics of the source sound. From this point of view, it is better to use an Eclipse amplifier.

There are many schools of thought on this subject. Linn for example say that more should be spent on the source (CD player, Turntable) and less on the amplification or speakers. We on the other hand tend to think that balance is best; basically spend the same on each component. By doing this if you decide to upgrade your hi-fi at any time in the future you will know that your system will always be balanced. Also by balancing your system the features on your equipment.

Yes, as long as they are "powered" speakers. Powered speakers have a built-in power amp in one of the enclosures. Using an RCA patch cable, connect the left (white) and right (red) plugs to the left and right "Line Out" jacks on the back panel of the PSD300 or PSD340. The other end of the RCA plug connects to the input of the powered speaker.

Check what kind of connector the device has (e.g., stereo minijack) and buy the proper kind of cable to connect it to the system.

Answer: Yes, you can connect the WebRadio via a standard audio cable (cinch) to your Hi-fi set. It is also possible to connect the WebRadio to a set of headphones or external speakers. Depending on your headphones or speakers you might need an additional cable/plug. This cable is available in almost every audio shop or media mall.

Yes is the simple answer although you will need to purchase a plug adapter which has a moulded 2-way terminal block at one end and a polarised connector for plugging into your satellite or subwoofer at the other. These can be obtained from your local Mission dealer or, if you prefer, directly from Mission on +44 (0)1480 452561 or spares@mission.co.uk Back to Top

Yes. Our LCD/TV monitors come with an Audio Output outlet which allows you to connect external speakers to the monitor.

While the Ruby, Little Gem, and Little Gem MkII practice amps can be used with any speakers, best results are achieved with full-size speakers intended for use with guitar amps. The amps will work well with an total impedance of 4, 8, or 16 ohms. We've tried hi-fi speakers, clock-radio speakers, and auto speakers - they just can't cut it. For me, using anything other than a speaker designed for the frequencies of an electric guitar produced sounds more like a toy than an actual amp.