A - You can add a Serial Board or a Multi-Port Board (with serial ports) to add more serial ports to your PC which cost as very little . Or you could use a (Serial) Switch box to connect two devices to one serial port.

A - Standard Address Labels (1-1/8" x 3-1/2") in white, clear, blue, yellow, and pink and green The Smart Label Printer Pro supports a variety of labels sizes and types.

A#8.15: This is usually caused by serial port configuration problems. Common symptoms may be: % copycat .ttyco .ttya Error opening tty .ttya, aborting. or % /usr/sbin/getty 8bit.38400 .ttya getty: .ttya: I/O error The first thing to check is that the following GNO serial port drivers exist: /dev/modem /dev/printer Next, ensure the following two lines are in your /etc/tty.config file, and that they are uncommented: modem 2 .ttya printer 1 .

A#8.9: This answer describes hooking up a terminal to the printer port. Hooking one up to the modem port will be similar except that .ttya should be used instead of .ttyb. On the hardware side, you will need a mini DIN 8 to DB25 printer cable. This should be connected from the IIgs' printer port to the port on the terminal that would normally be hooked to a modem. Next, you have to run a getty(8) over the printer port. Add this line to your /etc/inittab file: pp:23478:rest::/usr/sbin/getty 8bit.

I've connected the USB to Serial adapter but it's on Com Port 5 (or higher) and your software only has Ports 1-4. This issue applies to the c\temp software only. This has been resolved with the new version of the MDAS-Pro software. If you do not have a copy of this software, please contact us.

A. When attaching a PDA cradle to the serial (RS232) port, verify that the port assigned to your HotSync and/or ActiveSync software is Serial USB (COMx). The PA090 COM port assignment can be viewed by clicking START, SETTINGS, CONTROL PANEL, SYSTEM, clicking on the DEVICE MANAGER tab, clicking the "+" sign next to "Ports (COM & LPT) and looking for a "Serial on USB (COM#)" entry.

Some laptop computers don't have serial ports, but they do usually have at least one USB port. There are a number of very inexpensive converter cables available. They use a device driver to create a serial port under windows operating system. The driver that comes with the converter cable must be compatible with your version of windows of course, and the USB ports must be functioning, both in hardware and in the operating system and in the drivers for the convertor cable.

If your computer does not have a serial port, it should have multiple USB ports. Connection to the computer is via the serial to USB cable included with the MiniStation (GWS-MINI-U). This is a common perception that is definitely incorrect. When you use a serial to USB cable, you also install drivers to make that USB connection look like a standard RS232 port within your computer. Your application software will be looking for a serial port (COM1, COM2, etc.) for data input.

Many new PCs (especially laptops) have USB ports but do not have the standard 9-pin serial ports found on older computers. This presents a problem because most of the GPS manufacturers don't make data cables that terminate with USB plugs. Unfortunately, we have noticed that the USB-Serial converters often cause computer crashes. We are working hard to resolve this problem.

No. The serial port and gameport are totally different. Even if you could find a physical adapter they would still not be compatible electronically.

The very short answer is: you can't do this easily. There are problems between the USB-to-serial stuff; problems with printer drivers; and problems with OS X (or OS 9, etc) not knowing about either. The G3's, G4's and iMacs do not have the old Apple "DIN-8" connector (serial Localtalk) for modems and printers. These later Macs either use USB or Ethernet. Regarding the DIN-8 and Appletalk, see a related FAQ question for a description of that port. I don't describe Ethernet or USB.

A. The Parallel Port on the USB Mobile Port Replicator with Ethernet does not provide support for Parallel Scanners.

A000030: If you use the serial port for printing or plotting you need to put the DOS MODE command into your AUTOEXEC.BAT file to set up the serial port before you run DANCAD3D.COM (tm) (if DOS MODE is in your AUTOEXEC.BAT file your serial port will be automatically set up each time you turn your computer on.) Some plotters require a "NUL MODEM" type serial port cable to operate.

USB to Serial Support - Use a direct/single USB to serial cable, and stay away from multi-port "hubs". Unplug the serial cable to the weather station when changing PC connections, like from serial jack to USB jack. Power down the weather station before connecting the serial cable.

Yes but you must purchase a USB to Serial converter. We have the IOGEAR USB to Serial Port Adapter Model GUC232A available under RIGblaster Accessories. All of the software was written for serial port control so it will not work directly with a USB port. With the USB to RS232 serial adapter you can add the function of a serial port to a computer that doesn't have one or doesn't have and extra one.

You will need to add a serial port to the computer to be able to connect it to a TNC. There are several companies making serial port adapters that connect to the computer through the USB port. Most require that the operating system in the computer be Windows 98 or later (or a Mac OS). Once that serial port has been connected to the computer and recognized by the operating system in the computer, it should be available for any Windows (or Mac) terminal program to use to communicate with the TNC.

The RT/2127 software can not share the serial port with other active software. For example, if you have a PDA cradle normally connected to COM1: and the PDA software is active on COM1: you will receive an error from our software when attempting to use the port.

ANSWER: You can use a standard 9-pin serial cable to go from a computer to a LC unit without needing an adapter. However, if you'd like to use cat5/network cable then you would need one RJ45-to-DB9 female for the computer side and one RJ45-to-DB9 male adpater for the LC side. If you would like to connect more than one LC unit to the computer in this manner simply use a RJ45 splitter in the line to provide more connections.

Yes, but since the voltage levels on the RS-232C serial port is ? 12V you have to use an interface circuit like