Low tension checking springs, Part Number 99881-2, must be used (instead of your normal spring) to mock up your valve train and to check the piston to valve clearance on the engine. Assemble the valve train and verify correct lifter preload or valve lash. By mounting a dial indicator on the cylinder head with the plunger?s tip on the valve spring retainer, you can quickly check the clearance.

The critical point for both valves is the ?Overlap Period? as the exhaust cycle is ending and the intake cycle is beginning. You must start checking the clearance before and continue after T.D.C. on both the intake and exhaust to be sure you have the correct readings through the overlap period. You can find all the tools required for checking valve to piston clearance (as well as degreeing a cam) in Crane Cams? Tune-A-Cam Kit, Part Number 99030-1. See similar questions...

The time between measurements is automatically controlled. Relative humidity in the chamber has to decrease back to ambient RH level, before the VapoMeter is ready for next measurement. The ventilation period is longer after high values (after 10 g/m²h about 10 seconds and after 100 g/m²h about 60 seconds). See similar questions...

Omron Blood Pressure Monitors are not intended for use during exercise or activity. We recommend you avoid eating, smoking and exercising for at least 30 minutes before taking a measurement. Back to Top See similar questions...

Make sure you always follow these steps before taking a measurement. For at least 30 minutes prior to taking your measurement do not eat, smoke or exercise. Rest comfortably in a relaxed environment for at least 15 minutes prior to taking your measurement. Don't take a measurement after physical activities or during stressful times. Take the measurement in a quiet place. Back to Top See similar questions...

In certain situations, law enforcement are not able to clear an offense know to them by making an arrest (see Cleared by Exceptional Means, p. 80). UCR Handbook Often they have exhausted all leads and have done everything possible in order to clear a case. If agencies can answer all of the following questions in the affirmative, they can clear the offense exceptionally for the purpose of reporting to UCR. See similar questions...

This type of tests provides information on the glomerular and tubular function of the kidneys. The kidney tubules' main function is to excrete waste products while reabsorbing water and dissolved chemicals from the ultrafiltrate. See similar questions...

Generally, there is no specific “spot” to put the holds. The wall is your canvas, and the holds your paint. Generally speaking, on a traverse wall, it is good to put the smaller holds across the bottom of the wall and the larger jugs across the top. This enables the kids to have a good place to put their feet while still having enough hold to hang onto as they learn to traverse the wall. On a full height wall, routes can be set at different difficulty levels. See similar questions...

Forged pistons expand at a faster rate than cast or hypereutectic aluminium units and therefore require a greater piston to bore clearance. The engine may sound almost diesel-like until it warms up because the pistons rock in the bores at TDC and BDC, but oil consumption isn't increased and engine longevity isn't compromised. See similar questions...

experienced contractor will cause less damage than a novice. Ask the contractor to test a small area to determine. See similar questions...

Distance to target - For good reflecting surfaces the VibroMet™ 500V can measure targets at any distance between 1 cm and 5 meters. If the surface is not a good reflector, then the maximum distance may be less than 5 meters. Frequency of vibration - The VibroMet™ 500V can measure frequencies from DC to 20 kHz. There is also a version that will measure up to 50KHz. Velocity of vibration - This parameter has a maximum value of 1. See similar questions...

If no error message on the screen appears, the measurement is good. A suspect measurement is indicated by a "REPEAT" error message on the screen. See similar questions...

There are three parameters that define the measurement requirements: 1) distance to target, 2) frequency of vibration, and 3) velocity of vibration. Distance to target. The typical range of standoff distances of the MB-LDV is about 0.5m to 1.5 m or 2m to 6 m. The optical configuration should be optimized for each standoff distance. Frequency of vibration. The MB-LDV VibroMet can measure frequencies from 5 Hz to greater than 20 kHz. Velocity of vibration. See similar questions...

Environmental measurements are often reported in dimensionless units such as part per million (ppm). If 1 liter (1.06 quarts) of water were involved, then 1 ppm would amount to 1 milligram (mg) per kilogram (kg) (1 L). This could also be expressed as 1 microgram per g. Other commonly used units include parts per billion (1 microgram per kg) and parts per trillion (1 nanogram per kg). See similar questions...

Measurement methods are Axillary, Ear, Oral and Rectal. The core temperature, or the temperature of the internal organs, is most accurately reflected in a rectal temperature. Different body parts have different temperatures. Usual differences are: See similar questions...

The NCEP ATP III recommends that LDL be directly measured as a new feature of the guidelines. LDL is not directly measured in today's routine lipid panels. Rather, it is calculated using the Friedewald equation: [LDL] = [total cholesterol] ? [HDL] ? [triglycerides/5]. Thus, calculated LDL is falsely low in patients with elevated triglycerides, and it does not correlate well in patients with diabetes, coronary disease, or other atherosclerotic diseases. See similar questions...

FerriScan is a post-image processing service that returns a liver iron concentration measurement. As inputs it requires 5 single spin echo series of axial images with TR = 2500ms and TEs of 6ms, 9ms, 12ms, 15ms and 18ms respectively. The report returned contains a liver iron concentration expressed in two different units (mg of iron / g of liver tissue dry weight and mmol of iron / kg of liver tissue dry weight) and as an age adjusted measure (mmol/kg/year). See similar questions...