Traditional putty knives are NOT recommended. A high quality pull scraper which is pulled toward you instead of pushed away from you is essential with the Speedheater Infrared (IR) Paint Remover. Heating the paint will soften the paint. It is then up to the quality scraper tool to get the paint off. Most paint on the surface will require a little elbow grease when scraping. Inexpensive scrapers found in many paint stores do not work very well.

The Window Glazing Chisel is designed to be held perpendicular to the glass at a roughly 45 ° angle from vertical, to remove the glazing that holds the glass in the frame.

A tongue scraper has two rows of plastic serrated scrapers on one side and two rows of bristles on the other. The scrapers gently clean the tongue, while the bristles reach into the tiny grooves on the surface to dislodge bacteria and debris.

Slaked lime putty is quicklime (burned limestone) that has been mixed with water and allowed to age. Slaked lime putty for frescoes is finer than regular slaked lime, and it's been aged longer in order to make it smoother. This is crucial for frescoe work, which depends on very smooth surfaces.

Traditional paint scrapers are NOT recommended. A high quality pull scraper, that is a scraper that you pull towards you instead of away from you, is essential with the Speedheater 1100. Inexpensive scrapers found in many paint stores have not been designed to work with the Speedheater Method?. The scrapers we sell are top quality steel, manufactured to the highest standards in Sweden.

They both work well for filling scratches but two-component glazing putty (uses a hardener to setup) doesn't shrink and has many of the same properties as regular plastic filler. The traditional glazing putty that comes in a tube, like a giant tube of toothpaste is usually a laquer-based product that has several downfalls. Because it hardens by evaporation it is prone to shrinkage. It must be applied in only thin coats and must fully dry before final sanding or coating with primer.

You can use any scraper that you like, but some scrapers are more efficient, and will make your project a lot easier. Speedheater scrapers are designed to be pulled toward you with both hands, which requires much less energy than using a putty knife. A putty knife is designed to be pushed away from you at a shallow angle, which causes strain on your hand and wrist.

Glazing putty is thinner and creamier. It often comes in a can and uses a hardener to set up just like regular body filler. It's designed for filling smaller dings, crevices and sandscratches. It is very resistant to pinholing. It's often used as a second or third coat over bodyfiller to fill pinholes or sand scratches or other imperfections in the regular body filler. It can be sanded with finer paper and leaves behind a nice smooth surface after sanding.

A screen scraper is quite simply a programming script that collects information from a webpage or other datasource and stores it for later browsing or filing. Screen scrapers are also called data scrapers, page scrapers, content scrapers, data harvesters and probably a dozen other similar names.

As long as you have the necessary support on your computer or server to allow the scraper to run, yes.

A bench scraper is a tool used to clean your work surface and for dividing bread dough. You may also use it for working with chocolate.

These protocols are all used to run a remote session on a computer, over a network. PuTTY implements the client end of that session: the end at which the session is displayed, rather than the end at which it runs. In really simple terms: you run PuTTY on a Windows machine, and tell it to connect to (for example) a Unix machine. PuTTY opens a window.

Roof Membrane system is a high build elastomeric or flexible coating, designed specifically for Roof Restoration. Unlike generic paint which produces a lower film thickness, offering less protection against the elements.

Yes, BST stain penetrates the surface of the material it is applied to. While a paint product adheres to the outer surface. BST stain sinks into the substrate and bonds below the surface.

There are two major differences: (1) materials - weld decay occurs to normal, un-stabilized steels while knife line attack occurs to stabilized steels; (2) location of attack - weld decay occurs in the heat affected zone (HAZ) while knife line attack is located at the fusion line.

The single most important difference between J. Bruce Voyles, Auctioneers and most online auctions is our 35 years in the knife business. But that's not all. We police our auctions. Fakes are returned to the consignors. All knives we sell are available for inspection prior to completion of the deal. Our live auctions inspection is open to anyone, and we encourage all bidders to point out any knives that may have been tampered with.

Gil Hibben designed the knife that was used by Sylvester Stallone playing John Rambo in the 1988 movie "Rambo III". The movie studio licensed the knife design to United Cutlery to make replicas of the movie knife (which, by the way, was their biggest selling knife worldwide). The United Cutlery replicas were manufactured in Taiwan and are actually about 2 inches shorter and has a thinner blade than the knife that was used in the movie.

The Gamma Knife Perfexion? precisely focuses 192 beams of gamma radiation on a specific target area of the brain, with each beam originating from a slightly different point. Highly sophisticated computer software is used to determine the size, location and shape of the area to be treated. Only at the point where all 192 beams cross is enough radiation delivered to affect the diseased tissue, while sparing surrounding tissue.

This noninvasive technology treats patients with abnormalities that are located within the brain or that are too close to delicate structures and blood vessels (though it is most effective on targets less than four centimeters in size). Almost a third of all the patients treated with the Gamma Knife since 1968 have sought relief from blood vessel problems (i.e. AVMs). Nearly two-thirds were treated for brain tumors, including cancer, glial tumors and rarer types of tumors.

The individual beams of gamma radiation are not strong enough to damage any tissue as they travel through the skull to the treatment site. At the site, the beams join together pecisely to act in the same way a surgical "knife" would to treat the abnormality.