There is no danger in doing this, but you will get light only in the middle one of the three "on" positions.

Yes. We carry all replacement lamps for our beds. When you are ready to replace your tanning lamps, call our customer service department. Lamps are upgraded by the manufacturer every year, so it is important for you to call us to get the most compatible tanning lamp for you tanning equipment. We offer the lowest prices on all Wolff tanning lamps and will be able to offer advice when wanting to upgrade your lamps to a stronger tanning lamp.

We recommend C-9 lamps with mounting clips. C-9 lamps are available in 10 watt and 7 watt sizes. We stock pre-made bulk light line and lamps in a variety of colors for this purpose.

The Axis ballast is available for 32 watt T8 lamps, in 4' length or 2' "U-bend" style. We offer 2-lamp, 3-lamp, and 4-lamp 120 & 277V ballasts. We highly recommend using the 32 watt "Super T8" (high lumen) fluorescent lamps.

We use the very fine stained glass in the shades of the Tiffany lamps, and zinc alloy in the bases of the Tiffany lamps.

It is simply a matter of preference. Some people insist that only clear bulbs should be used. Others, including us, prefer using colored gels or bulbs. We use blue in our cemetery, amber against our large, brown stucco mansion fa?ade and a blue on one side and green on the other side of our old farmhouse fa?ade which has a lot of white highlights in it. Clear bulbs are just too stark for our tastes.

A - Yes, fluorescent lamps do flicker, but the newer technologies that utilize electronic ballasts operate at levels where the flicker is beyond human perception. The older magnetic ballasts operate on 60 cycles per second (60 Hz), and the lamps actually flicker on and off 120 times per second. Many people feel they can see them flicker, especially in presence of computer or TV displays.

Each lamp is carefully carved out of the crystal salt found in the foothills of the Himalayan Mountains. After that, each lamp is securely attached to its base with screws.

The calculation for any question like this is to divide 150VA by 50W, the whole number that you get is the most lamps you can fit on that transformer. In this case the answer is 3.

The answer to this is a definitive NO. Colour cameras are typically fitted with an IR cut filter and will not allow IR light in excess of 700Nm to pass resulting in the camera performing poorly in these circumstances.

The original "Gou Gong" TDP lamp was tested by Chongqing Environmental Protection, the China Measurement Institute and others and found to have no harmful effects. The lamp was exhibited at the 1986 Zagreb International Fair in Yugoslavia in competition with 560 inventions from 18 countries and was awarded the Gold Medal. At the 1986 Brussels Eureka World Fair for Invention, Mr. Wenbin received the Silver Medal Award.

A - Yes. With the cost of electricity going up dramatically, all incandescent lamps that operate for more than three hours a day should be replaced with CFLs. Fortunately, the prices of CFLs have been coming down dramatically. CFLs equipped with electronic ballasts can now be purchased for less than $10.00 in many locations. CFLs are three to four times more efficient than incandescent sources and last many times longer.

A - T-8 lamps are an excellent choice for retrofitting into a lighting fixture that has T-12 lamps. It will be necessary to change the old magnetic ballast(s) to efficient electronic ballast(s). At the same time the fixture, lens and/or louver should be thoroughly cleaned. It may also be possible to reduce the number of lamps if the task being performed has changed since the lighting was installed - for example the use of computers that has replace paper-based tasks.

Any method that does not put stress on the glass envelope and/or the lead-to-glass seal on the lamp end is acceptable. Most common methods are to solder the leads (with a strain relief bend) directly into a PC board, or to secure the lamp ends with a custom silicon end cap.

Remove irradiator cover by removing both knobs at each end of the LIA and lifting out the assembly by its handles. Clean the replacement UV lamp and reflector liners with a lint free cloth and denatured isopropyl alcohol. Use latex or vinyl gloves during this step to keep the lamp free of any fingerprints. Place one lamp lead and end fitting through the mounted metal air diffuser and on top of the lamp holder.

Each brand of tanning lamp has a different life expectancy, typically 800 to 1000. We recommend residential tanning lamps be changed about every 3 years. Replacement of tanning bulbs in commercial tanning equipment .varies with usage.