Yes, the CB-USB4 cable that comes packaged with the camera is required to connect the camera to the computer. The stock number for a replacement cable is 200 776. It can be purchased through the Olympus Emporium or 1-800-201-7766.

Yes, the CB-USB4 cable that comes packaged with the camera, is required for downloading images using the camera. The stock number for a replacement cable is (Item #200776). It can be purchased through the Olympus Emporium or by phone at 1-800-201-7766.

The USB cable (I-USB7) provided with the Optio43WR is also compatible with other Pentax Optiocameras such as the Optio550, Optio555, OptioS, OptioS4 OptioS4i and Optio40.

The camera has a cable that is 9.8 feet (3 metres) long. USB allows you to add hubs that provide an additional 16.4 feet (5 metres) between a hub and up to six segments. Therefore, it can be extended 30 metres (98 ft).

Yes, the CB-USB4 cable (packaged with the camera) is required for downloading images from the camera. The stock number for a replacement cable is 200776.The CB-USB4 cable can be purchased from the Olympus Emporium at http://www.olympusamerica.com/store, or by calling 1(800) 201-7766. The KP-16 Connector Cable, part number 200337, is required for direct printing from the S-HD-100 or my S-DVD-100 to the P-S100. The KP-16 Connector Cable can be purchased from the Olympus Emporium at http://www.

When Quickview installs it creates a directory in the following location: C:\Program Files\FLIR Systems\Device drivers. All the drivers required for USB and Firewire cameras are in this location. They can also be found on the Quickview CD.

Yes, the OneTouch USB Cable can be used with a hub, rather than connected directly into a port on the computer. With the 9-pin serial cable, just plug it into your meter and the serial port (COM port) of your computer. You may need to restart your computer if another device had been using the serial port. With the OneTouch USB Cable, you must install a software driver before using it for the first time.

If the distance between USB slots of your PC/notebook is too far for USB Y-cable to connect, you can only connect prime head of USB Y-cable, as indicated below, to one USB slot of your PC/notebook; and then connect the other USB slot of your PC/notebook with DC-inlet cable's USB head to supply power. Therefore, the power supply head of USB Y-cable is useless.

Partly from Apple's Manual "About Cables" ftp://manuals.info.apple.com/Apple_Support_Area/Manuals/newton/0308266ANCBLS.PDF] You can connect to your Newton using either a serial cable or an ethernet card (connection from a 2.1 device to MacOS computers only). Please note that using an Ethernet card means first installing the proper driver. The MP1x0 devices and the eMate 300 have a Mini-DIN-8 RS232 and LocalTalk compatible port.

Please make sure the USB cable is made by Fortuna, and please download USB driver and firmware upgrade instruction from GPSmart download page for you to install the USB cable.

You will need a standard usb cable (the one that is included in the box when you buy the phone). Because you are going to use a usb cable you have to install drivers for this cable. You can find this drivers at the downloads page If you do not have this cable you can buy it from us. For now go to contact site to ask us for the cable. You can also buy it in every electronic store and ebay. It's often the same cable as used to connect digital (video) camera's to a pc.

Good question. According to the USB spec, software is required to connect not only to first tier devices, but also to any plugged into USB hubs. It appears that there is a bug in the Kodak Mounter and USB connection software causing it to fail unless the camera is "device #0", connected directly to the computer.

No! The labs are equipped with computers for your use, and any equipment required for assignments, such as video cameras or tape recorders, are available for check-out.

You need an RJ45 cable with connectors on both ends. You may purchase a 14' cable from SATS in the West Building or at one of the local computer stores. Students who reside off campus can obtain internet connectivity via a modem through an outside Internet Service Provider (ISP) or through a service provided by the University called Merit or MichNet. The charge for MichNet service is $40 a semester or $100 for a year.

The remote cable RM-CB1 can be connected to the power battery holder HLD-3. The RM-CB1 remote cable cannot be connected to the camera body directly.