Means that the crossroad has a flashing red, but that the signal goes into normal operation if a car triggers a sensor on the crossroad by waiting a given amount of time. Flashing green/red resumes soon after. (These have likely been removed from the state.) Same as DE's, but only found at crosswalks, and triggered by a button pushed by pedestrians. May be located at a side road or crossroad with a stop sign so the cross traffic can take advantage of the red time on the main road.

Set the time. If the time has been set, a timer program may be set to record and there is no tape in the unit. Either insert a blank tape or delete the timer program.

The ink light turns on when the Printing Mailbox begins to run low on ink. Although your messages may continue to print correctly for a short time, the words will soon begin to fade and the image colors may not look correct. We recommend that you have a spare cartridge on hand to insert when you are ready to replace the old cartridge.

Use only plain, letter-sized (8.5 x 11-inch) paper in the Printing Mailbox. Do not use any other types of paper such as cards, envelopes, photo paper, or transparencies. If the paper light continues to blink after you've tried the above solutions, check that the Printing Mailbox cover is closed properly.

Approximately the size of a quarter ? the exact size of each product is listed next to the animated image of each item, along with the number and colors of lights.

A blinking light on your printer can indicate normal operation, a warning, or printer malfunction. The blinking light may be green, amber, red, slow, normal, fast, and implication will vary from model to model. On our current models, a green ready light that blinks once/second usually indicates that the printer is receiving data. A red or amber error light that blinks once/second usually indicates a printer error (paper out, paper jam, cover open, printing error).

This section was written by someone who wishes to remain anonymous, but I will field any questions on the subject -IDB] Yes. When two loads are connected in parallel (such as with a Y-cable) they get the same voltage as each other. They do NOT get the same voltage as if only one load was connected because the head-unit has an internal resistance (typically around 600 ohms).

A window unit is a self-contained packaged air conditioner. All components are housed within the unit. It is installed through an opening in the wall and no inter-piping connection is required. A single split, as it is called, comprises 2 parts that make up a system air conditioner: the outdoor unit (condenser) and indoor unit (Fan coil). The FCU is a cooling coil that cools the room, interconnection piping between the condenser and fan coil is required to run this system.

To provide more flexibility in configuring the system. Now, users may place the codec in a cart, or in a rack—whichever best suits their room needs.

A split system uses indoor and outdoor components to provide a complete home comfort system. A package unit or self-contained unit requires no external coils, air handlers, or heating units. Leave all interior doors open at least 2 inches if the room does not have its own return air intake vent. Have your heating and cooling system thoroughly cleaned and tuned (not just a check-up) by a reputable company with certified technicians, at least once or twice a year.

If a team is below the cap, then their Disabled Player, Bi-Annual, Mid-Level and/or Traded Player exceptions are added to their team salary, and the league treats the team as though they are over the cap. This is to prevent a loophole, in a manner similar to free agent amounts (see question numbers 29, 30, 31, 32). A team can't act like they're under the cap and sign free agents using cap room, and then use their Disabled Player, Bi-Annual, Mid-Level and/or Traded Player exceptions.

Our Visx Star S4 IR excimer laser has a feature called ActiveTrak 3-D Active Eye Tracking. It captures all 3 dimensions of intra-operative eye movements, follows your eye and adjusts accordingly also insuring that the treatment center is set to the center of your pupil but without dilation. If your eye moves too far out of range, the laser automatically stops in 1/50th of a second and resumes treatment when your eye is realigned.

It seems like Vancouver is unique in having some of the traffic lights blinking green at various times of the day. The blinking light means that the light is not on a regular change cycle but can be activated, when needed by a pedestrian or cyclist.

It's telling you some very specific, though coded, information by its color and blink rate. It could be you need a new lamp, or that the security feature has been engaged rendering the projector useless until overridden. Check your user manual's troubleshooting guide. Status light meanings are projector model specific. Call us if you get stuck!

During the procedure an eyelid holder is used to hold the eye open and the doctor can stop the procedure at any time if you look away or need to sit up. The computer will remember exactly where the doctor stopped the treatment and it will not have an impact on your outcome. Again, since the laser is a cool laser, there is no damage to the adjacent tissue and even if you somehow blinked, nothing would happen to your eyelid. BACK TO TOP

No. Do not remove the USB Flash Disk when the LED is blinking. Removal at such times may cause the loss of data or the damage of the FAT table when writing to USB Flash Disk. However,if the USB Flash Disk is not functional after being pulled out during data transfer, the user can reformat USB Flash Disk without causing any damage to the hardware. Not at this time. The necessary USB driver must be installed from the supplied floppy, or by downloading it from the our web sites.

When the battery is running low, the light will begin by flashing slowly. At this point you can still use the doppler for some time. As the battery becomes too low, the light begins blinking more rapidly and will eventually shut the doppler off. The doppler unit requires regular 9 volt batteries that can easily be replaced by removing the small panel in the back of the doppler.

Safe-T-Beam® is a safety device that must be installed and operating properly in order for the garage door opener to work. If the Safe-T-Beam® LED indicator is flashing, it indicates an error condition. First be sure that the lenses are mounted 6” from the floor on either side of the garage door opening. If the LED continues to flash, click here for a list of possible causes and solutions.

Instructions for typing special characters such as exponents, the degree symbol, and the Greek letter mu depend on your computer's operating system and what particular software you're typing "at," among other things. Following is some general advice; consult your computer's "help" system or other documentation for further assistance.