Aerosol valve diptube length is measured from the top curl of the mounting cup to the bottom of the can. Pump diptube length is measured from the top of the land to the deepest point of the bottle. We require an actual bottle sample to determine correct diptube length.

Yes we do! A left handed action costs $ 100.00 more. We aren't picking on you, it just requires different set-up and tooling so it costs a little more. Most companies don't even give you the option. See similar questions...

Crank arm length is measured in millimeters from the center of the crank bolt to the center of the pedal spindle (where the pedal attaches to the crank arm). The most common sizes for crank arms are 165mm, 170mm, 172.5mm, 175mm and 180mm. Crank arm length is generally a function of two characteristics; leg and riding style. See similar questions...

The Most important size you need is the clamp diameter. There are usually four sizes that are used while purchasing a stem. These are all the four different sizes. 1", 1 1/8", 1 1/4" or 1 ??". By far, the most common size is 1 1/8", used on almost all mountain bikes and many road bikes. Some road bikes use 1". Finally, 1 1/4" is used by a few rare mountain bikes. Stems also come in various lengths so you can achieve a more precise fit on your bike. See similar questions...

To Measure your Torso Length, begin at a point on the spine level with the top of the hipbone or Iliac Crest. Measure along the curve of the spine up to the base of the neck or top of the seventh cervical vertebrae (the prominent bone or large knuckle at the base of the neck, or when bending the head backpacks, the crease of the neck) Typically, you would measure the Torso Length vertically in a straight line, and not along the curve of the spine. See similar questions...

The length of a lamp can also be referred to as the Maximum Overall Length or M.O.L. Most lamps are measured from end to end including the base. Linear fluorescents are an exception; they include the actual socket in their M.O.L. See similar questions...

a general guide hold your arm out in front of you and measure from where your thumb joins your hand to your chest. This is the measurement we suggest you use. This total length will include the length of the head of the poi the cords and the handles. However there is no reason why you can not have it shorter. If you have it longer it will restrict some internal moves when swinging in front of your chest. See similar questions...

The most important measurement of a goal stick is the length of the paddle. A good rule of thumb for measuring a goal stick is if the toe of the stick is off the ice when the goalie is in his crouch, the paddle of the stick is too short. If the heel of the stick is off the ice when the goalie is in his crouch, the paddle of the stick is too long. Paddles come in varying lengths between 21 and 26 inches. See similar questions...

The way to measure the needed length if from the tail shaft seal face to the differential mounting face. See similar questions...

Yes. The wing tube ends after the mounting bolt and before the end of the paper socket intentionally to avoid having a high point of stress where both tubes end together. See similar questions...

A - 35 mm - 1.380" or the top of the steerer tube must extend 1/32" past top of steerer clamp. (See instruction sheet) Note: The insertion length must be measured after any spacers are added below the bottom of the stem. See similar questions...

It's true the mast was surprisingly rigid given its length. In fact, once it was deployed, we didn't expect the mast tip to move by more than 15 centimeters (5.9 inches) for the rest of the mission. Unfortunately, that much motion is very significant for the SRTM height measurements. For example, an error in our knowledge of the mast tip position in the "worst" (baseline roll) axis of only 3 millimeters (1/8 inch) would result in a height error of about 9 meters (29.7 feet). See similar questions...

a general guide hold your arm out in front of you and measure from where your thumb joins your hand to your chest. This is the measurement we suggest you use. This total length will include the length of the head of the poi the cords and the handles. However there is no reason why you can not have it shorter. If you have it longer it will restrict some internal moves when swinging in front of your chest. See similar questions...

If you have a tape measure, put it around your neck with the end at the front. Measure the length that you would like to have the necklace hang at around your neck and read off the length. If you do not have a tape measure, use a piece of string to find the length that you would like to have the necklace hang. Using a ruler, measure how long the piece of string is to the length that you wanted. See similar questions...

The tubes can be made of any durable substance that is capable of holding a vacuum. Every route will have special requirements according to local conditions and economics. Some possible materials include but are not limited to: Sealed concrete, glazed ceramic, steel, aluminum, fiberglass, and plastics. See similar questions...

Plaques: For a basic size estimate for cast plaques, count the number of characters and spaces then divide by 4. This provides the typical plaque size in square inches, allowing for plaque design features such as borders, heading, font sizes, etc. Various other criteria factor in, including the use of a logo. Sign Letters: They are slightly less in width than height. To ballpark a line length, identify your cap height, then multiply by the number of letters in your copy. See similar questions...

Click here for the printable driveshaft measurement sheet. When complete, fax measurement sheet back to Classic Chevy 5-Speed at (760)438-2271 for immediate processing. See similar questions...

Early pedometers were mechanical and used a moving lever arm to count steps. Electronic pedometers now detect movement through a spring loaded, counter-balanced mechanism that records vertical acceleration at the hip. Pedometers measure the number of steps a person takes throughout the day. See similar questions...

Answer: No, because the finite system does not include a tube lens to bring the parallel rays to focus. See similar questions...

Answer: Although you may be able to screw the objective into the nosepiece, the presence of a tube lens in the light path will result in a deteriorated image. Answer: No, that would not be advisable. The focal length of Olympus' tube lens (180mm) is not the same as that of other manufacturers. As a result, the magnification of the objective would not be accurate. See similar questions...