UNI EN 1519-1 standards indicate 95°C, whereas the softening point, namely the temperature which causes the piece to deform corresponds to 125°C. Therefore, even temperature peaks exceeding 95°C do not create problems.

The Thermorotor is able to deal with relatively high pressures. On the process side, the pressures may run up to 20 bar(g) and on the medium side 6 bar(g). The standard model permits temperatures of up to approx. 200 ?C. Variations are possible following consultation. See similar questions...

Since Polyethylene melts at 250 F, but softens at a much lower temperature, we recommend that the maximum fill temperature be 180-190 F. See similar questions...

For the operational state of most PolySwitch products the usable range extends up to 85°C ambient. For some product families (i.e. PolySwitch TD, Chip, AHR, and RHE devices) this can be as high as 125°C ambient and for others, such as the PolySwitch VTP device, it may be as low as 70°C ambient. In a non-operational state, some devices (i.e. PolySwitch SMD, miniSMD, TS) will withstand solder reflow temperatures for a short duration. See similar questions...

This depends on the product family in question. For the operational state of most of our products the usable range extends up to 85°C ambient. For some product families (some TD, Chip, AHR, and RHE devices) this can be as high as 125°C ambient and for some others (VTP) this is as low as 70°C ambient. For a non-operational state some of our devices (SMD, miniSMD, TS) will withstand solder reflow temperatures for short duration. See similar questions...

Grade Braking is not intended to reduce the need for great care by the driver when driving a heavily loaded vehicle down a grade. Drivers should continue to take all normal and appropriate actions to keep the vehicle under control at all times. See similar questions...

A - In our first generation, it will be on the order of 250C, as set by the curie points of the piezo elements regulating spacing. Because of the broad selection of materials available to us, operation will go well above 1000K. We have a known failure of 2 years’ operation at 1600K continuous, and 10 years at 1200K. This is why we position Power Chips as the ideal waste heat recovery technology -- getting more power from a given quantity of fuel. See similar questions...

The higher the temperature, the faster the fermentation process, and the faster the sugar will be used up and converted into acid. See similar questions...

PVDF pump heads have an operating temperature rating of 212 deg. F (100 C). However, these pump heads can be autoclaved (non-operating) at temperatures up to 240 deg F (116 C). See similar questions...

The maximum temperature is determined by the membrane. Maximum temperatures range from about 60°C to 130°C (140°F to 266°F). High temperature VSEP systems can operate at 130°C with a Teflon membrane. See similar questions...

Maximum junction temperature can be calculated using the following formula: Tj = TA + P[QJA] ; Where TA = Ambient air temperature, P = Power(watt), and QJA = Theta JA What is the difference between operating free-air temperature, and operating ambient temperature? They both use the same symbol TA. Operating free-air temperature and ambient temperature are the same, with typical temperature at 25 degrees Celsius. See similar questions...

The maximum continuous operating temperature is 180oF and is capable of 212oF for intermittent use. Fusion LockTM seals are recommended for high temperature applications. See similar questions...

The maximum temperature for the spun bond polyester pleated bag is 200? F and the maximum temperature for the spun bond Nomex pleated bag is 365? F. Top See similar questions...

Polyethylene storage tanks have a maximum storage temperature of 120 degrees F. Contents with a temperature in excess of 120 degrees F-even for a short period of time-can weaken the tank's structural integrity and make it susceptible to deformation and failure. See similar questions...

The maximum operating temperature of standard gas springs and manifold systems is 80?C/ 176?F. However, high temperature gas springs and manifold systems are available. Contact Hyson Products for more information. See similar questions...

DuraTeck sheets can be exposed to 700 degrees F without changing color. Exposure to higher temperatures tends to darken the color. The degree of darkening will vary depending on temperature variations across the stainless steel. See similar questions...

The maximum temperature is based on MIL-C-23183 specifications. Most ceramic capacitors are rated for a maximum temperature of 125?C and glass capacitors at 85?C. A complete response to this question can be found in the Jennings TechNote C-1: "Vacuum Capacitor Characteristics " See similar questions...

We do not recommend our units to be used in any situation where fluid is heated beyond the maximum tolerance level of the PVC internal washers. To protect the integrity of the De-Bug unit, fluid temperature at 10% below the maximum tolerance level would be a safe figure to use. Say 70 degrees Celsius maximum temperature. See similar questions...

degree F (CodeLine™ offers such high operating temperature as a standard feature in its OCTA series. Check the product bulletin of respective model for standard operating temp). See similar questions...