A standard incandescent dimmer can be used to dim either line voltage (110V AC) or low voltage (12V AC) lights with an electronic transformer. The DC transformers are only dimmable with low voltage electronic dimmer controls, whereas, the AC transformers are truly dimmable with incandescent dimmer controls.

No, it is an electronic timer switch, not a time clock. After you have pressed the on/off button, it will turn off the lights when the time limit expires. No. The TS can be programmed to scroll through the time delay options by holding the switch down for four seconds.

Yes. Some heaters have built in thermostats, but they can either be removed or inactivated. Remote thermostats can be located so that they are more convenient to adjust than the built in one. Located across the room from the heater, they will also insure that the heater runs long enough to heat the whole room. This is especially true in an odd shaped room where air does not flow readily from one section to another.

To use a compact fluorescent bulb on a dimmer switch, you must buy a bulb that's specifically made to work with dimmers (check the package). GE makes a dimming compact fluorescent light bulb (called the Energy Smart Dimming Spirals®) that is specially designed for use with dimming switches. We don't recommend using regular compact fluorescent bulbs with dimming switches, since this can shorten bulb life.

A 1k linear pot is fine, it will dimm from zero to full brightness. Radio Spares or Farnel is his best bet ( farnel Part no 350-140 ). Please note: XCOM radio feature change. Radios after serial number 1150 feature a new LCD backlight controller which has a switch mode power supply. These units are not able to be dimmed and work down to around 4 V.

This can be done, however the CNK200 requires wall that is thicker than normal 4" wall. (Please verify this information with out Technical Support Department since the total thickness from the bezel's bottom edge to the last hinge for table-mount bracket attachment looks to be less than 4" as per the diagram posted on our website.) The termination switch should be ON if the local monitor is connected through a straight cable.

We have heavy-pull (Neodymium Iron Boron) magnets available for purchase. The typical refrigerator "give away" magnets do not provide enough strength to hold much to the mag?wall. Some people find that a larger strip (sheet) magnet works well by attaching part of the magnet to the mag?wall, and the rest of the magnet overlapping the paper.

Yes, as long as the type of cable used is approved for such use and the dimmers are not drawing more than the rated current carrying capacity. The feeder cables typically used in the US' Entertainment industry, Types SC and W, have a 290 Amp rating for size 2/0. Yes and No: "Type W" and "Entertainment" (actually "Type SC") are 2 different types of feeder cables. TMB sells 2/0 cables of both types.

If a product purchased as a 3-way control needs to be used in a single-pole application, cap off one of the traveler wires with a wire connector.

Response: A dimmer switch can be used with "bright fixtures," such as chandeliers, pendants and even bath lights, to adjust the amount of light given depending on the activity of the room. To use the dimmer switch effectively, use brighter lighting for parties or dim the lights for a quieter, more intimate setting.

To enhance your home decor a dimmer switch can be used with any decorative lighting fixtures, such as chandeliers, pendants and even bath lights, to adjust the amount of light given depending on the activity of the room. To use the dimmer switch effectively, use brighter lighting for parties or dim the lights for a quieter, more intimate setting

The useable reach is the distance from the fixed point, such as the wall location to where the tubehead will be aimed (the end of the collimator). This depends on the arm length. Please refer to question number 5.

All of the products we sell are made to order. So when you place your order, your product is then made for you. What this means is that changing components, or making a bed a specific size or shape is no problem. We can not stress this enough. We do not charge for this service, so by all means take advantage of buying directly from the manufacturer.

Lutron dimmers are designed and tested to be installed and operated only in the mounting position (vertical) as indicated on the dimmer.

screws to the ceiling surface. The wiring compartment has a standard size knock-out on top and is 3” in Yes. socket sets are supplied in 6 foot lengths and may be cut to a desired length; follow the detailed instructions supplied with the socket. No, doing that can harm the other transformers. Remove the inoperative fixture immediately. Take one of the operating units and install it in the inoperative location.

Yes, you can. For detailed directions, look up the owner's manual or wall-mount kit instructions, because all such models can be easily wall mounted. Such kind of intermittent issues can prove to be very tricky. I would recommend contacting both your dealer and the Sony technical support team in order to avoid problems that may crop up in future. From your description it is tough to understand the possible issue with your TV set.

I've installed all the filters and plugged in the DSL modem but I'm not getting any internet connection. The "Ready" light is blinking. I've removed all the phone devices from their respective phone jacks and only have my DSL is connected but the Ready light is still blinking.