Pillars have a memory! The first time you burn your pillar, set its memory by leaving it burning one hour for every inch of diameter. Failure to properly set your pillar's memory will cause it to form a tunnel that burns all the way to the bottom. Generally your pillar should not be burned for more than six hours at a time to avoid over-warming the sides and causing them to cave in.

You can use a candle holder, a ceramic container, or a glass dish.  We suggest covering any dishes you use in aluminum foil for easy clean-up. Whatever you choose to hold the candle, it must be fireproof, and it must hold or contain the candle securely until it is burned all the way out. See similar questions...

Drafts again are the culprit - causing the flame to burn to one side. Another reason could be that the holder is not resting on a level surface and the wick is not centered and straight. See similar questions...

One hour per inch of candle container diameter. For Example, if you have a 3 inch diameter container, burn the candle for 3 hours, then extinguish. If you extinguish the candle before the liquid wax or "melt pool", is all the way to the ends of the container, you will have problems in the future with even burning. If you let the candle burn longer than what is recommended, or "power burn", your candle will burn down much quicker. This happens for several reasons. See similar questions...

We recommend complete disassembly, cleaning, reassemble and oil. Burke's Gun Oil creeps and crawls getting it into places that might not normally get an oil coating. See similar questions...

As tempting as it may be to use ALL the wax in the jar, you need to stop burning your container candle when the wax level reaches ? " from the bottom. If you continue to burn your candle, you run the risk of the glass container breaking or possibly shattering. See similar questions...

The first time that you light the candle, you should allow it to burn until it has a complete layer of melted wax across the top of your candle. (This layer is called the melt pool) When putting the flame of a candle out, you should either use a wick dipper, or if you must blow the candle out, then put your finger up between you and the candle, then blow. This will help prevent pieces of burned wick from flying into your candle wax. See similar questions...

There is no reason to burn your gel candle to the very bottom. You may risk a potential fire problem if you do. Burn the candle to about 1/2" from the bottom. See similar questions...

Razor burn or 'redneck' affects about half of all men that shave. It is the result of minor skin abrasions caused by the friction of the razor as it passes over the microscopic folds and ridges of the face. Sweat and harsh shaving products further irritate the skin, leading to tissue inflammation and dilation of the blood vessels (which causes the redness). The best way to avoid this is to make sure you shave correctly and look after your razor. See similar questions...

It is safe to burn your personalized, custom Photo Candle as long as you follow our Candle Care burning instructions: See similar questions...

The visible crater is some 190km wide but can be assumed to be about 270-300km across judging by other evidence. It would be better to call it the Vredefort Structure or Ring. The widest of the concentric rings forms today's "Ring of Gold" - the external ring of the crater stretching from Johannesburg around to Welkom where South Africa's gold wealth has been mined. See similar questions...

Pixel-orbiting is an improvement but it does not eliminate the danger. Philips, Samsung, Pioneer, NEC, Sony, Fujitsu and Hitachi all offer plasmas featuring such technology. Many of these companies have trademarked names for it. Pixel-orbiting may work against bright lines but will not work against bright solid blocks. Pixel-orbiting blurs the edges of burned-in blocks so that they appear less objectionable. Some stand-alone devices are now sold that add pixel-orbiting to a VGA signal. See similar questions...

Are prices subject to change without notice? For more answers not posted here, please contact us at info@middlepillar.com. See similar questions...

Before you light your candle, you should ask yourself if you have ample time to let your candle burn for a sufficient amount of time. For example, if you continually burn your 16 oz. Apothecary jar candle for 1-2 hours at a time, it will not be enough time to create a wax melt pool for the entire diameter of the jar, therefore, it will only burn down the center, leaving wax around the jar. See similar questions...

The crater will be in view of the flyby spacecraft for a time after the impact. From images obtained of the crater by the flyby, the depth of the crater should be able to be determined by analysis of the shadow along one side or by counting pixels in the image and accounting for the slope of the crater. Either method will produce an estimated depth, not an extremely precise measurement. See similar questions...

To 'anoint' an object, basically means to rub or smear something on it. Anointing a candle is usually done to amplify or focus its energy on a specific task. It can be done with oils, powders, herbs, etc. See similar questions...

Once the female starts her incubation, termed 'sitting the clutch' or ' sitting tight', the eggs can be candled after 6 - 7 days to check for fertility. You can use a small pen light flashlight or an Egg Candler. A large degree of care should be given when handling the eggs. If you need to pick them up, you should use a plastic spoon. I try not to handle the eggs and just candle them in the nest. To candle the egg just place the light directly against the egg. See similar questions...

Candling should be done eight days after the first egg. This should enable you to see the beginnings of a series of veins under the shell: if it is fertile. If it is not fertile, eight days is enough to provide you with some certainty that the egg is devoid of life or hope for it. Dead in Shell eggs should be removed from the nest, unless some chicks have already hatched,and you want to ensure that the hen does not sit too tightly on the new chicks, by leaving an egg. See similar questions...