If theunit is beeping there are 3 possible causes: You have either had a leak, the batteries are low, or it has not been tested for two years. If you have had a leak, dry the sensor, fix the leak, and hold the button above the LED light down until the Light stays lit and you hear a beep. If you do not have a leak, and the Leak Controller has been in service for close to two years, hold the button above the LED down until the Light comes on and the Leak Controller beeps.

If you want to make this the default action, put the setenv RADWARE_CURSOR_BELL n command into your .cshrc or .login file, or edit your .radwarerc file and change the line

Some ICD’s make audible tones for a variety of situations. Some are programmed to do a “self check” every day at a specific time. If there is a problem, broken lead, low battery, etc. it will make a noise. If there is a more immediate problem the device may emit a constant tone. If your device starts making a tone contact the doctor/hospital that monitors your device. They will advise you what to do next.

Well, you can use set noerrorbells but it does not turn off the bell for all cases. It only makes a difference for error messages; the bell will be always be used for a lot of errors without a message (e.g., hitting <Esc> in Normal mode). If you want Vim to stop beeping then all you need is :set vb which tries to do a screen flash rather than an audible beep. Some terminals can't do screen flashes, but if yours does and you don't want it to flash or beep then use :set vb t_vb=.

After the main alarm has been activated - there is a secondary beep that will signal approximately every ten (10) seconds. The secondary beep signifies that the cabinet has been opened and that the alarm system needs to be reset. Additionally, we recommend that you inspect you AED to ensure function and use. The RescueCase is equipped with a "Low Battery Detection" mean for the 9 volt battery.

Make sure sound is coming from keypad, (sometimes other sounds: pager, smoke detectors with low batteries, etc. sound similar) Place your ear near to keypad to be sure Beeping from keypad normally indicates a trouble condition, please refer to trouble conditions in your specific owner's manual

Five minutes before the time elapses on your Timer the Healthwave Sauna will 'beep' for 60 seconds, to notify you that your sauna session is about to end. When time is up the Healthwave Sauna will automatically turn off. Everything will turn off except the light, so if you have fallen asleep you won't over do your sauna session and you will still be able to see. This is a safety measure built into every Healthwave Sauna unit.

The beeping noise is a safety feature that all fitness equipment manufacturers include on the products. It alerts the user to a change during a workout that includes a change in the resistance level on an elliptical and the speed and/or incline on a treadmill. Back to top

The controller is the touch screen's "brain". Information from the sensor is processed and relayed to the computers CPU to activate the desired function.

A wind controller, sometimes referred to as a "wind synth", can loosely be defined as an electronic wind instrument. Wind controllers are, for no logical reason, most commonly played and fingered like a saxophone though models have been produced that play and finger like other acoustic instruments such as the trumpet, recorder, tin whistle, and others.

A Breath Controller is basically an electronic breath pressure sensor that is housed inside some form of enclosure that is usually held between the teeth or worn on the head as a headset and blown into. Its function is to measure the musician's breath pressure and translate that into a varying electronic control signal that can be used in some expressive manner. The control signals can be used to control devices such as analog and MIDI synthesizers, MIDI sequencers, MIDI lighting systems, etc...

Probably, depending on the specific tablet you have. Find the serial number on back of your tablet and call GTCO Technical Support.

Yes - the SRV-1 controller uses a Fairchild FAN8200 H-bridge for dual motor control. It's rated at up to 650 milliamps (1000mA peak) current. If you need to drive a larger motor, you can drive a larger controller from the SRV-1 motor outputs. There are additional outputs which can be used to drive hobby servos.

It's possible - you can find schematics and PCB layouts on http://www.surveyor.com/SRV_info.html. Check with us about the type of sensors.

Check the batteries. The low battery alarm will sound when battery power levels are below the operating range required by the telescope. You can turn off this alarm in the ULTILITIES menu.