Step 4 Attach the speaker leads to the red binding post (1+ and 2+). There is no connection to the black posts. Step 5 Turn on the amp and adjust the volume using the channel A level control knob (Channel B will no longer respond).

Connect the speaker leads across the two red binding posts, using channel one binding post as the + (hot) connection or on CE's with Speakons across pins 1+ and 2+ on the channel one output. See similar questions...

Yes. By building a summing Y-cable (check out Why Not Wye) and connecting it to the MAIN OUTPUTS a mono signal may be obtained. See similar questions...

This depends on the amplifier you have. Generally, you will first turn the power off, set the bridge mono switch to the bridge position and attach your speaker wires onto the two red binding posts of each channel. It is then necessary to apply your input signal to channel one on your amplifier and adjust the gain as needed. For some amplifiers, the gain of channel 2 must be turned all the way down while others are required to be all the way up. See similar questions...

Generally, the deciding factor to this dilemma is the total speaker load impedance you wish to drive. With Micro-Tech and Macro-Tech amplifiers you would want to use Bridge Mono to get the most power available when driving 8 or 4-ohm loads (one or two 8 ohm speakers). With a Power-Tech or Com-Tech amplifier you need to stay at 8 ohms or greater. Parallel Mono can be used when driving lower impedance loads. A one-ohm load can be driven Parallel Mono with a Micro-Tech or Macro-Tech. See similar questions...

Unfortunately there is no way to obtain a mono headphone signal from this mixer. The use of a single cup mono headphone is not advised either as it can cause distortion in the headphone amplifier. (See below for system mono option.) See similar questions...

Not yet, but the client side API for authentication is not the problem. We will likely have a lot of other authentication APIs, like the Liberty Alliance APIs. The problem is people on the web provider end that might use this for authentication. See similar questions...

Some amplifiers which are both bridgeable and able to drive low impedance loads also allow you to use "mixed-mono" mode. This involves driving a pair of speakers in stereo mode as well as simultaneously driving a single speaker in bridged mono mode off of ONE pair of the amp's channels. See similar questions...

Yes. The CP 64 has a Zone 1 Mono Switch located internally, directly in front of the Priority Assign switch. See similar questions...

Use our Mono Migration Analysis tool to check if everything that your application uses has been implemented in Mono or if there are special considerations to keep in mind. The Mono API today is somewhere in between .NET 1.1 and .NET 2.0, see our Roadmap for details about what is implemented. See similar questions...

No, it will not. Microsoft Office is a Windows application. To learn more about running Windows applications on Intel UNIX systems refer to the Wine Project (http://www.winehq.com). See similar questions...

Note: For those amplifiers with IOC (Input-Output Comparator) the channel two IOC indicator will illuminate when the unit is operated in Parallel-Mono. Note: CE Contractor Series (CH/CL Series) CP660, D Series and K Series amplifiers cannot operate in a Parallel-Mono mode. See similar questions...

Yes, AdScientist has full support for the scheduler mode. You can set a time period or set the day during the week to bid, plus the frequency of bidding. Within the property area for the account you want to autobid, simply go to the "Autobid Setting" section and enable the scheduler for this account and set the frequency of the auto bidding. Select the keyword or keywords you want to autobid with, then click on the "Property button" on the tool bar. See similar questions...

Either set will provide a summed LEFT plus RIGHT mono signal. You can use both LEFT and RIGHT outputs simultaneously when needed, (like when you want to run two channels on a power amplifier without connecting a Y-cord.) Yes. The internal Program Priority Release Time control, located near the Line 2 and Line 3 RCA input connectors, can be rotated to change the interval from five to twenty seconds. Clockwise rotation increases the release time interval. See similar questions...

For increased power. If your amp can handle the load, it will put out more power through a bridged channel than it would into through a non-bridged channel. Theoretically, a "perfect" amplifier that puts out X watts into Y impedance into each of two channels will put out 4X watts into Y impedance into one bridged channel. See similar questions...

Yes you can but it is relevant to use mono from the SVN repository, because the actual release (1.1.8-3) is not able to compile or execute that code. The RAPPTOR.Persistence MySQL driver works with the MySQL .net connector 1.0.4. Using the pooling in this connector makes a problem sometimes. This behavior is by design. See similar questions...

Setting the XiNCOM Router in Transparent Bridge Mode allows the use of public IP addresses on a private network. This is useful if you have a firewall behind the XiNCOM Router such as a Cisco PIX or Watch Guard. No Firewall or DHCP functions are available to the public IP PCs. See similar questions...

Logging in: Using a SSH you will be provided with a login prompt. The default username is "admin" and the default password is "1234" Setting up the Ethernet cards: Under the Interfaces menu choose Ether1 then IP Assignments menu. If needed select the default IP 192.168.1.1 then click the Edit button to change the card the IP address. The IP you provide will be the address that the RWV will use to connect to the up-stream network. See similar questions...

Yes. Placing the 2Wire in to Bridge Mode effectively disables all routing functions, NAT, DHCP, and anything else beyond Layer 2. This is accomplished by going to Management and Diagnostic Console (MDC) section at page Advanced- Configure Services (&homeportal/tech/configuration.html) and then UNCHECKING the Routing Enabled box. Make sure you follow and understand the Warnings on that page before you uncheck the box so you will be aware of how to get back into the 2Wire as disabling routin... See similar questions...