Yes, the OneTouch USB Cable can be used with a hub, rather than connected directly into a port on the computer. With the 9-pin serial cable, just plug it into your meter and the serial port (COM port) of your computer. You may need to restart your computer if another device had been using the serial port. With the OneTouch USB Cable, you must install a software driver before using it for the first time.

No, the USB port will support only one user. If you need to support multiple computers you need to use the Ethernet port and a hub/switch.

A USB hub typically consists of a single upstream port (designed to connect directly to your computer or to another hub) and multiple downstream ports. D-Link provides both 4-port (DSB-H4) and 7-port (DSB-7) models. It allows you to expand the number of devices you can attach to your computer.

Good question. According to the USB spec, software is required to connect not only to first tier devices, but also to any plugged into USB hubs. It appears that there is a bug in the Kodak Mounter and USB connection software causing it to fail unless the camera is "device #0", connected directly to the computer.

No. The Hitch will recognize the hub connect to the first device it finds on the USB hub. If that device is unplugged from the hub, the Hitch will then search for another device connected to that hub, but will never connect to more than two devices at once. No. The Hitch is a bridge device, and contains no memory. This is an advantage because it cannot have any issues with storage, such as hard-disk failures or memory allocation errors. No.

Yes, as long as the hub uses an external power supply. We do not recommend or support this configuration. Before requesting help from Technical Support, please try connecting the device directly to the computer's USB port.

Yes, you can connect the player directly to your computer using an Ethernet crossover cable. You can purchase a crossover cable at most retail computer stores. Once you have this connection, you'll need to set up your network adaptor and Squeezebox with static IP addresses so that they can find each other.

A hub is a network device that extends the network so that you could connect more than one computer to the network jack. A network hub can be borrowed from the ITS department. Verify if your hub has a button called Normal/uplink near the rightmost end. It is not necessary that your hub should have the Normal/uplink button. If you see the button, make sure you press the button inwards to set it to uplink.

Yes- The phone should work properly when plugged into a USB hub. If experiencing problems with a vPhone using a USB hub, plug the vPhone directly into the computers USB port.

Yes. SELECT customers may have up to four computers connected simultaneously. However, CLASSIC customers may only have one computer connected to the network at a time. Yes, with Choice OnLine you can surf the Net and simultaneously make phone calls or watch TV. To use a fax machine or dial-up modem while surfing the Net, you must have a normal phone line available. Your computer will not allow you to use our Choice OnLine service and dial-up to another Internet service simultaneously.

A USB cable and the presence of USB connections are not yet adequate for exchanging data successfully. However, data transfer can be effected using a USB cable if a serial COM Port is emulated by the GPS receiver. The GPS data must be available in the NMEA 0183 format when data is called up online, so that Geogrid is in a position to evaluate these data.

The HP Advancestack 100Base-T Hub-8txe and the ProCurve Networking by HP 100Base-T Hub 8 can only be directly connected to another Class II 100Base-T hub or to a switch. To connect them to a 10Base-T hub, either use a switch in between, or connect them to the ProCurve Networking by HP 10/100 Hub 12 or 12m or ProCurve Networking by HP 10/100 Hub 24 or 24m which are both Class II hubs that autosense the speed of each port to be either 10Mbps or 100Mbps.

Only the computer which has been registered with ResNet will be able to access the network outside your room. The remaining computers will not be able to communicate with resources outside your residence hall. Using a hub or switch can potentially cause your port to stop responding to all traffic.

In total you should only connect 5 tiers of USB hubs together. A tier is defined by the number of hubs a device's signal must pass through before it reaches the host. For example, using the DSB-H4, D-Link's 4-port USB hub, you could connect a theoretical maximum of 341 hubs in five tiers, this would leave you with an incredible 1024 ports to connect USB devices! But you should only connect 127 devices together at any time. Do not add a 6th tier of USB Hubs.

There are a number of USB bridges on the market. These devices allow a direct connection between 2 PCs via their USB ports. However, D-Link recommends using a DSB-650 to add Ethernet networking via USB. Two computers can be connected either via an Ethernet Hub (DE-805TP/C - the "Hubby" is a great choice for a home network) or via a cross-over cable. USB bridges are limited in their functionality. They effectively work by accessing a shared piece of memory built into the bridge.

This is becoming more of a common problem because a lot of computers are now coming out with just USB connections. The way around this is to either purchase a USB to Serial port converter, or contact the manufacturer of the product to see if they have a USB connection for the instrument.

Parts : mini-itx MII 12000, 512Mb RAM, WD 120Gb, Samsung 250Gb, OPUS 150W, Orinoco gold PCcard, external wifi antenna, BT GPS

Yes, the CB-USB4 cable that comes packaged with the camera, is required for downloading images using the camera. The stock number for a replacement cable is (Item #200776). It can be purchased through the Olympus Emporium or by phone at 1-800-201-7766.