Any length can be used. This antenna is impedance matched to 50 ohms to allow you to use any length required.

Generally it is not recommended, though it depends on the cable and the frequency you are using. In general the longer the cable between the antenna and receiver the greater the loss of signal strength. See similar questions...

Shortening the antenna reduces both sensitivity (range) and selectivity (ability to sort good signals from bad). See similar questions...

The maximum length for a USB cable is 5 meters (197 inches). The power transferred through a USB cable that is greater than 5 meters in length will start to decrease, and the device may not function properly. See similar questions...

A We find that it is very important ... especially with high performance top-loaded antennas. Your safest bet is to use 18 feet (5.5 meters) coaxial leads on all of your CB installations. See similar questions...

The maximum length of a 1-wire cable is dependent on several issues such as the type of cabling. Thirty meters is possible with modular phone cabling,... See similar questions...

Approximately 30 feet of shielded VGA cable, then you may need a distribution amp. Sometimes you can push this distance. Try the cable first, then order the amp if you need it. Some projector models have a Power off feature. If turned on, the projector will power down after some minutes of inactivity. This feature is to prolong lamp life. If this is painful, go to the power menu and deselect the power off option. See similar questions...

Length is not a restrictive factor. We have successfully treated submarine cables that stretched across Lake Erie that were 19,200 feet long. See similar questions...

Easy Engine v1.4 is designed for optimal performance with OS Windows 95, 98, 98SE, ME, NT4.0, 2000 and XP. Easy Engine is designed for optimum performance with DNA Engine and Tetrad software version 3.0B or higher. Using Easy Engine with other software versions (lower than 3.0B) restricts Easy Engine from some operations and features. These restrictions and limitations are applicable to "Explorer" and "Incubate" functions. "Monitor" functions operate normally. See similar questions...

There is no required length of a cable for an Amplifier to be active, a standard cable comes with the purchase. Please consider each model has different length of cable. See similar questions...

The total length for a FAMS network depends on the interface device being used. For a Network Interface (422-500) it is 5kms. However, if using a Terminal Server, it is 5kms per port and so it could theoretically be 20kms depending on the type. For more information, see our networking section . See similar questions...

We recommend Times Microwave LMR-series , Andrew Heliax , Belden RF-series or NK Cables USA cable for the lowest losses. Times LMR-1200 or Andrew LDF5-50A Heliax will produce 2.3 dB loss in a 100 foot run. Times LMR-400 and Belden RF400 will produce 3.3 dB loss in a 15m (50') run at 2450 MHz. Belden RG-213/U cable may also be used for runs of less than 7.5m (25'). Total attenuation should not exceed approximately 3 dB. Cables and connectors may be ordered through TESSCO. See similar questions...

Verify that the transmitter can be powered up by turning on the unit an observing the LED's lighting up. This verifies that power is connected to the transmitter Verify that the data cable is connected between port B on the Z-Max to the data port of the transmitter. Verify that the data port baud rates between the transmitter and the Z-Max are the same. A quick check is to use the COMM OPTIONS/PDL/LOAD function. See similar questions...

Pro16 A-Net cables can be 500ft/150m between devices with Cat-5e. Pro64 A-Net cables can be 400ft/120m between devices. See similar questions...

The slot spacing on the M/B is fixed to 0.8" apart. For convenience and to allow tolerance on the cable, Adex typically uses 1" per slot spacing to determine the needed cable length. For example, if a cable needs to reach from slot 6 to slot 4, then the cable length would be 2". This applies to the single ended flexible risers, as well as the wide cable used on the combo risers. See similar questions...

Well its all a bit of witchcraft and nonsense to me but our engineer has given me the following advice.... Try to get customers to cut their aerial cables to these optimum lengths. See similar questions...

When filling in your billing and shipping information in our shopping cart you will come across a text box called “Comments or Special Instructions”. You can either tell us what width your laptop is and we will send you the appropriate cable length, or you can request a specific cable length (20”, or 26¾”). If you make no special request for a different cable, your Jotto Desk will be shipped to you with the standard 22” cables. See similar questions...

The cable length was limited by a cable delay spec of 26ns to allow for reflections to settle at the transmitter before the next bit was sent. Since USB uses source termination and voltage-mode drivers, this has to be the case, otherwise reflections can pile up and blow the driver. This does not mean the line voltage has fully settled by the end of the bit; with worst-case undertermination. See similar questions...

m. however, if you cascade 5 hubs with 5m USB cables, this will allow you to connect a device 30m away. See similar questions...