To get audio from your TV through your AV receiver, please connect stereo audio cables from an available AV input on the rear of your receiversuch as D-TV/LD or CBL/Sat. Then refer to your TV owner's manual for more information about audio output to an amplifier. You may have to turn off the internal TV speakers in order to get any output from the TV into the AV receiver. See similar questions...

To connect the audio output from the computer to the AV receiver, you need a stereo mini-plug to a stereo RCA pin cord. Then connect the line-out from the computer sound card to an available audio input on the receiver. Select the input and adjust the volume output from the receiver. See similar questions...

Yamaha Music Australia provides a two year warranty for AV receivers. Any additional warranty periods are provided by dealers. Warranty issues that arise after the two years from the original date of purchase will be referred to the dealer where the unit was purchased. See similar questions...

Yes, many Yamaha AV receivers are stable down to, but not below 4 ohms. We recommend that you use only speakers with a minimum of 4 ohms. Also, please make sure that the impedance selector switch is set to the correct position as recommended by the owner's manual. See similar questions...

You typically have two options when connecting a powered sub woofer. Input (1) on the rear of the sub woofer would be used when connecting the sub woofer to the receiver using speaker wires. You would then connect the main speakers to the opposite end, or output or the sub woofer to the main speakers. Option (2) would be using RCA line level output jacks, input (2) on the rear panel of the sub woofer directly to the single sub woofer output on the back of an AV receiver. See similar questions...

In most cases, your TV may only have one set of video inputs. If this is the case then you are limited to the amount of video product that you can connect to the TV. By connecting all your audio/video components directly to the receiver, you would only have to use one video cable from the receiver to the TV. This in turn simplifies the connections, which makes video switching easier. See similar questions...

If the outlet was not connected to a receiver and TV when the DISH Network system was installed, it is most likely not connected to the satellite dish. The additional cable outlet may be added to the system, service call fees may apply. Contact your DISH Network satellite installer for more information. See similar questions...

The short answer is don't try if you are new to home cinema as the back of one of these machines can be very scary. If you are determined to do it yourself then talk to your dealer first to make sure you have all the right cables for your system, then carefully consult the handbook to ensure you have everything in the right place. You will then need to balance the speakers and set up the sound levels. See similar questions...

Because they aren't registered properly with Windows until you run a special Yamaha DSP application. Cakewalk Pro Audio 8.0x users can find the DSP updater on their Cakewalk 8 install CDs in a folder named DSPFactory. Run the SETUP.EXE file found in the DSPFactory folder to register your DSP Effects. Cakewalk Pro Audio 9.0 is ready to work with the DSP Factory right out of the box, no additional file installation is needed. See similar questions...

The Pro64? 6416Y2 A-Net Card is a bidirectional (16x16) card for Yamaha's MY slot. It can be used with Aviom Personal Mixers with an ASI A-Net Systems Interface module. Links: See similar questions...

The external input connections on the rear of the unit are designed for an MPEG2 processor that is very popular in Japan and was scheduled to come to the US. So at this point, there is no US made component that you can connect, short of a 6-channel separate processor that you can use for this port. At the present time, please ignore that section of your AV receiver. Currently, only the RX-Z9 and the RX-797 Stereo receiver are capable of accommodating a graphic equalizer. See similar questions...

All of Onkyo??s AV receiver are high current power design and its can be drive most of the speakers in the market. However the speaker system has its own specification with difference power requirement. Also difference brands speaker system has its own characteristics. So you are better to consult with the dealer and listen the sound performance you are searching for. See similar questions...

If your TV has stereo audio output jacks, use audio phono cables to connect these to the audio inputs on the receiver. Using the onscreen audio menu, switch the TV’s speakers off to listen through your stereo system and set the TV volume about ¾ of the way up. See similar questions...

If your current receiver has no subwoofer (RCA) line level output, you will need to connect the subwoofer to your receiver using speaker wire connections on the rear of the receiver. You first need to take the speaker input from the subwoofer to the A or B speaker terminals on the rear of the AV receiver. Then take the speaker outputs from the sub woofer and connect to the main speaker terminals inputs. See similar questions...

Audio Out is a feature which enables the LCD TV to provide an output port for audio so that external audio amps and speakers can be attached to it for creating a home theatre effect. See similar questions...

Make sure to connect a line between Combo card "audio out" and Sound card "line in". And connect your speaker to Sound card "line out". See similar questions...

All you have to do is make sure your computer meets the iChat AV system requirements. If so, and if you have Mac OS X 10.3 Panther, it's real easy to "turn" iChat into iChat AV--just plug in an iSight. Or, you can use a microphone and third-party FireWire (DV) camera that works with iChat and Mac OS X. Tip: To use a FireWire (DV) camera with iChat AV, your computer needs a PowerPC G4 or G5 microprocessor. See iChat AV: Does not recognize DV camera on computers with PowerPC G3. See similar questions...

If you are presenting for a PPPM class, PPPM Department has two LCD projectors with PC laptops available specifically for PPPM student presentations or faculty teaching use in our own classes and special events. Please come by or call Zudegi in the Dept. Office to reserve this equipment (room 119, 346-3635). If you are presenting for a CPW or other CSC project, the CSC has projectors and laptops for checkout. See Linda White in Room 111 (346-3889). See similar questions...

AV' stands for Audio Visual and is used to refer to Home Cinema systems. In basic terms, a Home Cinema system consists of a source, usually a DVD player, an amplifier, which has processing and amplification for five separate channels (or more) and a speaker package which consists of three speakers for the front (Front left, Right and Centre) two speakers for rear effects and a subwoofer. See similar questions...

stands for Address Verification -- a multi-step verification process - which accesses multiple databases to checks telephone numbers, billing address, recent change of address, high-risk shipping addresses, mailbox drops, reported theft priors, last 4 digits of social security number or other non-disclosed Driver's license, database of personal checks, and much more. There's no risk. Dealing with Faxcash Lite is "totally" safe. See similar questions...