Yes, you can connect the player directly to your computer using an Ethernet crossover cable. You can purchase a crossover cable at most retail computer stores. Once you have this connection, you'll need to set up your network adaptor and Squeezebox with static IP addresses so that they can find each other.

Mbps 802.11b and 54Mbps 802.11g are both supported. Both infrastructure and ad-hoc modes are supported, so you can connect to a wireless router, wireless access point, or even directly to a computer that has a wireless network interface. See similar questions...

No, the SRM 66 is a line level device. It will accept levels from consumer - 10 dBV or professional + 4 dBu sources but a preamp, like the MS 1b, is needed between the microphone and the SRM 66. See similar questions...

A hub is a network device that extends the network so that you could connect more than one computer to the network jack. A network hub can be borrowed from the ITS department. Verify if your hub has a button called Normal/uplink near the rightmost end. It is not necessary that your hub should have the Normal/uplink button. If you see the button, make sure you press the button inwards to set it to uplink. See similar questions...

Yes. SELECT customers may have up to four computers connected simultaneously. However, CLASSIC customers may only have one computer connected to the network at a time. Yes, with Choice OnLine you can surf the Net and simultaneously make phone calls or watch TV. To use a fax machine or dial-up modem while surfing the Net, you must have a normal phone line available. Your computer will not allow you to use our Choice OnLine service and dial-up to another Internet service simultaneously. See similar questions...

Sure. The onboard guitar preamp isn't usually necessary, but the AP 13 will work fine with most all varieties. Check to see if you need phantom power from the AP 13 though. This setting can be very important to maximizing performance with a second preamp. See similar questions...

The HP Advancestack 100Base-T Hub-8txe and the ProCurve Networking by HP 100Base-T Hub 8 can only be directly connected to another Class II 100Base-T hub or to a switch. To connect them to a 10Base-T hub, either use a switch in between, or connect them to the ProCurve Networking by HP 10/100 Hub 12 or 12m or ProCurve Networking by HP 10/100 Hub 24 or 24m which are both Class II hubs that autosense the speed of each port to be either 10Mbps or 100Mbps. See similar questions...

Only the computer which has been registered with ResNet will be able to access the network outside your room. The remaining computers will not be able to communicate with resources outside your residence hall. Using a hub or switch can potentially cause your port to stop responding to all traffic. See similar questions...

In any web browser, type in this URL: http://localhost:9000/. Replace "localhost" with the IP address for the computer running the SlimServer software. See similar questions...

Halleck Undergraduate Bistro, also known as The HUB, is located adjacent to the Cafeteria in Halleck Student Center. The HUB offers students a relaxing atmosphere in which they can enjoy a variety of sandwiches, salads, beverages, snacks, "Sub Connection" subs, "Freshens" frozen fruit smoothies and ice creams, and "Pretzel Logic" gourmet soft pretzels. See similar questions...

Enabling ConnectLive will allow callers or prospects to connect directly to you by pressing 0 at any time during your greeting. If callers elect to leave you a voicemail or fax, we store the message in your secure Inbox and you can retrieve the messages via phone or online at your convenience. Either retrieval method is cost free. See similar questions...

Yes, the OneTouch USB Cable can be used with a hub, rather than connected directly into a port on the computer. With the 9-pin serial cable, just plug it into your meter and the serial port (COM port) of your computer. You may need to restart your computer if another device had been using the serial port. With the OneTouch USB Cable, you must install a software driver before using it for the first time. See similar questions...

Good question. According to the USB spec, software is required to connect not only to first tier devices, but also to any plugged into USB hubs. It appears that there is a bug in the Kodak Mounter and USB connection software causing it to fail unless the camera is "device #0", connected directly to the computer. See similar questions...

C.6. I'm running Acorn Access. Is there any way I can share files over a serial link? I have SLIP set up, and I can ping one machine from the other with no problems, but I can't see its disks. See similar questions...

A hub and switch are two devices that split the bandwidth coming from any ethernet device that is connected to them they will not route communications from your LAN to the internet. All they do is split the bandwidth so your modem can see all of the MAC addresses connected to it so it will only give a connection to one of those devices. See similar questions...

No. The Hitch will recognize the hub connect to the first device it finds on the USB hub. If that device is unplugged from the hub, the Hitch will then search for another device connected to that hub, but will never connect to more than two devices at once. No. The Hitch is a bridge device, and contains no memory. This is an advantage because it cannot have any issues with storage, such as hard-disk failures or memory allocation errors. No. See similar questions...