The accuracy of a mechanical watch depends on numerous parameters, including the quality of the various components and the mastery of the timing adjustment, which we believe is the essential factor in determining accuracy.

The adjustment performed in horizontal and vertical positions (5 in all) enables Audemars Piguet to guarantee a daily variation in rate of the watch of between –3 and +12 seconds per day when it is worn on the wrist. Moreover, an index or inertia-block regulating system enables further fine-tuning of this result according to the indications provided by the wearer. See similar questions...

Assuming that proper processing is done, the accuracy is determined by the number of antenna elements. A four element array has a one sigma or typical accuracy of about 5 degrees and an eight element array has a one sigma or typical accuracy of about 2 degrees. For mobile operation, 5 degrees accuracy is more than adequate, but for fixed site triangulation, 2 degrees is much better. See similar questions...

Watches typically only wind when the crown is rotated so that the top part is moving towards the 12 o'clock position. Some people only wind the crown towards the 12 o'clock position and then turn the crown back a few clicks so that the oil that is used on the winding train doesn't sit on all of one side of the gears. However, the mechanism is like a Ratchet and it is intended that you can wind the watch with a back and forth motion too. Some people use the back and forth method. See similar questions...

A mechanical watch has a number of practical advantages. It is more than accurate enough for daily life, is very durable and, if well maintained, can be handed down from generation to generation as a precious heirloom. A good mechanical watch is often more accurate over a short period of time, such as a 12-second interval. Mechanical watches are also impervious to low levels of magnetism. See similar questions...

Depending on the movement used, the average daily rate will be between +15/­5 seconds per day. These rates are within the tolerances set and cover both automatic and hand winding watches. See similar questions...

A mechanical/automatic watch is a self-winding watch. The movement of your wrist and body causes the rotor, a weight attached to an automatic winding mechanism, to wind up the watch. An automatic watch needs no battery but will stop if not worn for over 40 hours. See similar questions...

Its best to wear a mechanical watch everyday or try to wind it every 3 days. All the wheels need to be in motion because when in motion it is actually oiling them up. See similar questions...

The digital watch is intentionally made to run a little bit fast (about 5 seconds per day). This allows the user to adjust the accuracy of the watch and results in more accurate timekeeping. You will need to measure and note how many seconds the watch gains per week. Once you have that value, do the following: Press the mode button a few times until the timekeeping mode is selected and the clock symbol is shown. Immediately push the select button again. See similar questions...

Compared with a quartz watch, a mechanical watch definitely shows less precision in terms of its timekeeping. These are fundamentally two different approaches to timekeeping. The differences in precision between the two technologies are substantial : A mechanical watch offers a degree of precision implying a variation of around 1 minute per week, 5 minutes per month, 1 hour per year. See similar questions...

A mechanical license grants the rights to reproduce and distribute copyrighted musical compositions (songs), including uses on phonorecords (i.e. CDs, records, tapes, and certain digital configurations). The Harry Fox Agency was established to license, collect, and distribute royalties on behalf of U.S. publishers that own and/or control the rights to musical compositions. See similar questions...

Yes, the system is 100% fully mechanical. It's a pure 100% mechanical trading system. It is based on Technical Analysis only without any kind of human influence. So the influences of human emotions like the famous Greed, Fear or Hope are removed from the trades. The system can even look too cold sometimes but it's an automated system so it's natural for it to work that way. See similar questions...

If you have recently installed Defensio, then try to be patient. The filter's learning algorithms take some time (usually no more than a couple weeks) to become very effective, so in the early days of installing the filter performance might not be what you'd hope for. Alternatively, if your blog receives a low amount of spam (say less than 100 comments per week) Defensio will have a smaller sample set to draw from, and may not perform to expected levels. See similar questions...

In Audemars Piguet watches, the minimum power reserve ranges between 36 hours for small-size watches and 40 hours for the larger ones. See similar questions...

We expect to be in limited production by third quarter 2001. However, we could have a machine built—without the latest beam delivery invention— and on its way to you in approximately four months from the time an order is placed. See similar questions...

Arbitrator Altman has already determined that "Any employees who have been displaced as a result of their NTE status shall be reinstated retroactively with back pay, benefits and interest, as required under the Back Pay Act." DFAS-Charleston will calculate the amount. See similar questions...

In theory, one standard PSI-5A sheet (1.5" x 2.5" x .0075") used as an "extender" can do .00035 joules of work on the outside world in a quasi-static cycle (i.e. a slowly executed sinusoidal cycle). When operated just under its first longitudinal resonance of 15 KHz, the theoretically available output power from the sheet would be around 5 watts. In practice it is difficult to collect more than 10% of this work. Resonant designs can be considerably more efficient. See similar questions...

Mondo-tronics' Robot Store, has Nitinol Kits, 1995 BEAM Games Guidebook and Solaroller do-it-yourself kits. There are many sources for BEAM parts. The best way is to just start collecting techno-scrap (printers, floppy drives, etc). You can also keep an eye on wholesale distributors for good prices on stuff. Below is a list of some parts for major components (and some sources) needed to build a BEAM walking machine (and other BEAM bots). Some (small) photovoltaic sensors (e.g., 0. See similar questions...

Mechanical diagrams are not included with most home plans. They are not needed for typical construction, and vary drastically among regions/countries depending on local codes. See similar questions...