If you are installing Windows XP on a system where you only have Serial ATA Drives you might encounter a problem where Windows does not seem to detect your Hard Drive and reports "No mass storage device found" during an installation (this occurs in Windows NT and Windows 2000 as well). This is because there are no SATA HD drivers in Windows XP/2K/NT and you need to load 3rd party drivers (just like with many SCSI drives).

Serial ATA is the latest standard in IDE(Atapi) devices. The maximum speed of Serial ATA is 150MB/s (the maximum speed of Parallel ATA is 133MB/s, the ATA133 standard). The cable for serial ATA has a minimum of 4 wires (extra ground wires can be applied), a 7-pin connectro and a maximum length of 1metre (about 3.1 feet). Because of the serial protocol only 1 device can be connected to each cable. See similar questions...

A3: SAS will be used in the same environments in which SCSI and Fibre Channel are employed today. SAS is designed to be used in high availability, enterprise environments where maximum random performance is required. SATA on the other hand is optimized for sequential I/O operations where the requirement is to transfer large sequential blocks of data to and from a drive. See similar questions...

Yes, however, some other manufacturers' drivers may incorrectly assume a PCI-X Sonnet card is another SATA card; kernel panics may occur; the PCIe cards are not suspect to this problem. See similar questions...

Because SATA II is nearly four times faster than Firewire and over six times faster than USB, it is the ideal interface for audio and video editing applications, high-end graphics, and all your other capacity hungry applications that demand continuous high performance throughput. A7. When an external drive without RAID fails, all data is lost. Without RAID a failed drive can mean the loss of hours of irreplaceable creative output. See similar questions...

The serial number location can vary depending on the drive series. The serial number is usually on the hard drive label or located on the front edge of the drive (the opposite edge of the connectors) on a bar code sticker. It is typically eight characters long and may appear as four characters on top of four other characters. See similar questions...

A. When attaching a PDA cradle to the serial (RS232) port, verify that the port assigned to your HotSync and/or ActiveSync software is Serial USB (COMx). The PA090 COM port assignment can be viewed by clicking START, SETTINGS, CONTROL PANEL, SYSTEM, clicking on the DEVICE MANAGER tab, clicking the "+" sign next to "Ports (COM & LPT) and looking for a "Serial on USB (COM#)" entry. See similar questions...

If your computer does not have a serial port, it should have multiple USB ports. Connection to the computer is via the serial to USB cable included with the MiniStation (GWS-MINI-U). This is a common perception that is definitely incorrect. When you use a serial to USB cable, you also install drivers to make that USB connection look like a standard RS232 port within your computer. Your application software will be looking for a serial port (COM1, COM2, etc.) for data input. See similar questions...

Serial ATA is a disk-interface technology developed by a group of the industry's leading vendors to replace parallel ATA. The group known as the Serial ATA International Organization (SATA-IO) owns the development of the Serial ATA technology and maintenance of its specifications. Scalability - Serial ATA is a point-to-point connection and allows multiple ports to be aggregated into a single controller that is typically located either on the motherboard or as an add-in, RAID card. See similar questions...

Microsoft does not provide installation/driver support for SATA hard drives in Windows XP. However, there are workarounds for Windows installs. The first two methods assume you have either a spare floppy or IDE drive to use temporarily. If this is not possible, you'll need to slipstream the drivers (see below). Copy the SATA drivers to a floppy disk (these can usually be found on your mainboard support disk. Usually these consist of PIDE/SATA Folders and TXTsetup.oem files. See similar questions...

While not native, SAS hard drives can be used on SATA desktops and workstations by adding a host bus adapter. See similar questions...

EIDE, SCSI, or Serial ATA (SATA) drive is not recognized during the installation of Windows NT/2000/XP. The installer reports that there is no drive present for the Windows installation, even though the controller recognizes the drive. The drive may not be detected during the installation of Windows because you have not yet loaded the drivers for your EIDE, SCSI, or SATA controller. See similar questions...

Many new PCs (especially laptops) have USB ports but do not have the standard 9-pin serial ports found on older computers. This presents a problem because most of the GPS manufacturers don't make data cables that terminate with USB plugs. Unfortunately, we have noticed that the USB-Serial converters often cause computer crashes. We are working hard to resolve this problem. See similar questions...

No. The serial port and gameport are totally different. Even if you could find a physical adapter they would still not be compatible electronically. See similar questions...

We do not support using the drive connected via an ATA card. Please connect the drive using an IDE connector on the motherboard. In addition, some motherboards have four IDE connectors rather than two. In that case, we would recommend connecting the drive using IDE-1 or IDE-2. For details consult the manual or the manufacturer. See similar questions...

A12. Serial ATA is an evolutionary replacement for the Parallel ATA physical storage interface and will allow future enhancements to the computing platform. Specifically, the thinner Serial ATA cable addresses OEM's concerns regarding airflow around the Parallel ATA cable and enables design of smaller PC chassis, as well as silicon vendors concerns regarding 5-volt tolerance support in future designs. See similar questions...

Yes, but it depends on the operating system (Mac OS or Windows) used. Sonnet Tempo Serial ATA PCI, PCI-X, and PCIe (PCI Express) cards only support drive hot swapping when used in Mac computers running Mac OS. SATA drive hot swapping is not supported in a desktop or server PC running Windows XP, Server 2003 or Vista. A SATA drive appears to the system as a not-removable hard drive and there is no mechanism in Windows to prepare the drive for removal. See similar questions...

Approximately $100 to $200 for a case with power supply, plus the cost of the hard drive, plus the cost of the SCSI-TV. Buy a tape drive that is recommended by your backup software. We have tested ARCHIVE and TEAC tape drives using "AmiBack" backup software. See similar questions...

You will need a 2.5" notebook to IDE adapter or cable to connect the notebook hard drive to the IDE port on your mainboard. Please make sure that pin1 (the red wire on the IDE cable) is connected to pin1 on the notebook drive. Pin1 is always located right next to the jumper pins on the notebook drive. See similar questions...