Yes. There is an idle timeout of 10 minutes. You will be disconnected when there is no data transfer between your device and the Access Point after 10 minutes.

This error is caused by a setting in your FTP client, that limits the amount of time your FTP client will wait for a server to respond. In order to fix this problem, increase the "server timeout" setting; a setting of 180 seconds should be enough time to connect to the archive.org servers. If you use SmartFTP, the "server timeout" setting can be found in Tools > Settings > Connections. See similar questions...

If you timeout or lose your connection, you should wait at least 20 minutes before attempting to start the application again, so that you will not experience a "cookie lock." If you do timeout or lose your connection, you will need to begin the application process from the beginning. Please ensure that you set aside at least 30 minutes to complete the application. Your application is only good for the specific position and location listed on the vacancy announcement to which you applied. See similar questions...

by default the IP is 192.168.1.168 Mask is 255.255.255.0 You have to add an IP address to your workstation that is within the same subnet. See similar questions...

Yes. The VPNS service has a four hour timeout window. This means that when the service has been connected four continuous hours it will automatically disconnect. To reconnect you will have to re-run the program and login again. See similar questions...

Yes. There is a session timeout of 2 hours. You will be disconnected from the Wireless Service automatically when the session terminates. If you are connecting to a VPN, the VPN connection will also be terminated at the same time. Or whenever the customer shuts down the device or is out of the hotspot wireless coverage, his/her connection will end after 10 minutes. (10 minutes Idle timeout - If no data transfer between the client and the AP, the connection will be dropped after 10 minutes) See similar questions...

This error is caused by a setting in your FTP client, that limits the amount of time your FTP client will wait for a server to respond. In order to fix this problem, increase the "server timeout" setting; a setting of 180 seconds should be enough time to connect to the archive.org servers. If you use SmartFTP, the "server timeout" setting can be found in Tools > Settings > Connections. See similar questions...

First, check if you are running a 2.4.20 kernel. If yes, please apply immediately the patch from https://bugzilla.netfilter.org/cgi-bin/bugzilla/showattachment.cgi?attach_id=8! The 2.4.20 kernel did contain a bug resulting in lots of bogus UNREPLIED conntrack entries (see https://bugzilla.netfilter.org/cgi-bin/bugzilla/show_bug.cgi?id=56). The answer is easy: UNREPLIED entries are temporary entries, i.e. See similar questions...

If you are using minicom on the host PC, make sure that the lrzsz package is installed. It is not installed by default. The minicom does not give any indication of error if you attempt to use a file transfer command that does is not installed. First, make sure that the login prompt was not obscured by other console messages. If I have a pcmcia or CF sleeve on when it boots, then messages from cardmgr often make it difficult to see the login prompt. See similar questions...

To turn the inactivity timeout to a longer session you must set the timer in the CW Admin utility. You can find either utility in the RW CAREWare business tier directory (Default location: C:\Program Files\CAREWare\RW CAREWare Business Tier). Open the utility and press "Stop Server". Select "LocalNumberStorage" from the table name combo box in the upper right corner. Select the tag "UserTimeout" and click "Edit". The Settings field will become enabled on the top box. See similar questions...

Users are able to reach the SpamCop site and parse/report small emails, but when trying to submit a large spam through the website form they get a time-out error after clicking the "parse" button. This is a problem experienced by users with firewalls. It may be a personal hardware/software firewall you have employed or, there may be a firewall on your ISP's network "protecting" you that you are not necessarily aware of. See similar questions...

This happens when your mailbox is VERY large and our POP server is trying to make a backup of your mailbox (for safety). Sometimes it takes longer than your mail program is willing to wait. For Outlook or Outlook Express, try increasing the Server Timeouts setting in the Advanced section of your their mail settings. For Eudora, add the following line to your Eudora.ini file, after the "[Miscellaneous]" section: Network Timeout="3000" See similar questions...

Opening My Portfolio page (click 'MY PORTFOLIO' button at Real-Time Quotes) will be keep session alive. As long as My Portfolio is open, session will be kept alive. See similar questions...

With a session-based service like QuestionPoint, we must maintain some type of timeout to free system resources. You can change the length of your QuestionPoint timeout period. The default length is 30 minutes. You can choose 30 minutes, 1 hour, or 2 hours at Home > Home > Settings. The Knowledge Base provides a 120-minute timeout period for adding, editing, and updating records. Also, when your Chat Monitor is active, no timeout period applies until you close the Chat Monitor window. See similar questions...

First Connection (FC) is a peer to peer support program. The program matches interested individuals with trained volunteer survivors who have been through treatment for the same diagnosis. The goal of the program is to provide individuals with support, information and hope from people who have had similar experiences. See similar questions...

Expression Connection is a tool for simultaneous searching of the results of multiple microarray studies for gene expression data for a given gene or ORF. The datasets searched and their references are listed on the Expression Connection page. Expression Connection may be accessed directly from the SGD home page or from its link on the Search Options page. See similar questions...

Sometimes a direct connection gets lost, but BitWise does not immediately recognize the lost connection. This can happen when the connection is not gracefully closed, such as when someone resets their home router or their ISP drops out for a minute. The typical symptom of a lost connection is that you do not receive message receipts for the messages you send. You can "reset" a direct connection by using the Reset Connection option on the Actions menu (in a conversation window). See similar questions...

Yes, there is no additional charge for multiple computers. Our service requires a router to separate the customer's network from Phoenix Internet'. The router acts as a firewall to protect the customer's home network from Internet attackers and is an administrative demarcation point that allows customers to build their home network independently. See similar questions...

If the Inactivity Timeout is attempting to exit while a user is in fact no idle, it would be because they are not performing any of the activities the Inactivity Timeout feature is looking for. To resolve this issue, you can either de-activate the Inactivity Timeout feature for the users in question using the Omni Tools Control Panel (Cards >> Omni Tools >> Control Panel) or you could use the following VBA code to update the counters. See similar questions...

Page timeout or expired can occur due to many reasons. You may get the message that page is expired or timeout if your website doesn’t respond within the time set by your web browser e.g. Internet Explorer, Netscape Navigator etc. Slow internet connection between your computer and our server may also lead to this problem. This is generally caused by your ISP (Internet service Provider), the company that provides your internet connection. See similar questions...