Most infrared heaters employ gas combustion (propane or natural gas) to heat a steel tube (tube heater) or ceramic surface (luminous heater), which subsequently emits infrared heat. It’s important to note how much infrared heat is emitted. You should also be aware that an infrared heater produces both infrared radiant heat (that is directed at people and objects) and convection heat that rises and is for the most part lost. See similar questions...

Most FIR sauna heater elements are steel-coated. Steel coating is an older technology that directs the heat source but requires more time to warm up, operates at higher temperatures, and uses more energy to reach the level necessary for deep tissue penetration. Now, ceramic-coated heater elements result in lower temperatures and more efficient energy use. Ceramic-coated FIR heaters produce the same useful energy as the sun at a very safe (. See similar questions...

The factory installed propane furnace does a pretty good job of keeping the pop-up warm, but you WILL go through a lot of gas. A normal 3 day weekend with evening temperatures in the 30's or 40's will use a full 20 lb tank of LP gas. If you're camping on an electrical site some people suggest taking along a small electric heater as well ... it will allow you to cycle the furnace off a little more and thereby us less gas. See similar questions...

This is a matter of personal preference. Infrared heaters will give you an instantaneous sensation of heat on your skin as long as you stay in range of the bulbs or element. Fan forced heaters raise the temperature of the air in the room so it will take longer to feel the heat. You are restricted to the line of sight that radiant heat requires. If you intend to use this as an emergency backup for freeze protection, definitely use a fan forced unit. See similar questions...

Schwank infrared heaters meet the strict European standards for efficiency and hence give you far more heat for your money. Our mission is to deliver the best in commercial and industrial heating solutions at the lowest life-cycle cost. Many North American manufacturers have attempted to capture market share by designing and building inexpensive, low efficiency infra-heaters that meet the minimum requirements of North American standards. See similar questions...

Yes, engineering studies supported by ASHRAE have determined that using standard infrared heaters the total BTU input of a heating system can be reduced by up to 15% compared to calculated design heat losses. Tests performed by a certified independent laboratory confirm primoSchwank and supraSchwank radiant efficiencies in the 65 to 82% range. This means the total BTU input with Schwank heaters can be reduced from 27% to 41%, depending on the Schwank infrared heater employed. See similar questions...

No. There could be significant differences in the infrared output, based on the burner material, configuration, operating temperature, mounting angles, combustion air input and reflector design. For example, on average, more than 50% of the heat generated by infrared heaters is convection heat, and in some inferior models the percentage of convection heat is as high as 65%. See similar questions...

HotZONE™ heaters fitted with IRLensesTM increase the amount of infrared energy in the central beam by 3 to 5X that of a conventional heater by "stealing " the energy from the shoulders of the radiation pattern. There is a sharp cutoff between the hot beam and the cold shoulders. See similar questions...

The Vegtherm is a 12 volt inline heater. It was designed specifically to heat vegetable oil to a maximum of ~ 70 C. (assuming an inlet temperature of min. 25 C...room temperature and matching the heater(s) to the task, namely the flow rate of fuel to be heated in a specific application). Power is supplied via a relay. In "two-tank" SVO systems, it is wired so that power is supplied to the heater when the fuel selector is switched to SVO. See similar questions...

Ans. Both types that is infrared and forced hot air heating system uses different method to create a comfortable temperature. Infra-red heats the air by using all three methods of heat transfer: radiation, conduction and convection. In other heating unit, the hot air rises to the ceiling and stratifies. It gradually work its way down to thermostat level hence the the floor slab never becomes warm enough to be comfortable. See similar questions...

the infrared energy penetrates, it safely and gently heats the tissues and blood within the affected area. The body's natural response to this increased temperature is to try to maintain a condition of homeostasis-a balanced environment or state of equilibrium throughout the body. To do this, the body responds with a rapid increase in blood flow to the area. See similar questions...

Far infrared energy (FIR) is a part of the natural light spectrum minus the UV element. The Infrared Body Treatment has been designed to output energy in the 5.6 to 25 micron FIR band also peaking around the 9.4-micron level to achieve maximum effectiveness. When FIR energy penetrates through the skin it transforms from light energy to heat energy and elevates the temperature of the subcutaneous layers. See similar questions...

Far-Infrared Ray Generating Ceramics Converts the body's natural heat to rays, facilitates blood flow and soothingly warm. Almost all adult diseases are closely related with the problems of the blood vessels. The flecks, fine wrinkles, rough skin, senility are all caused by the un-eliminated waste matters from the body system. But the health-enhancing bio-ceramic eliminate the waste matters in the blood vessels through capillary expansion. See similar questions...

Infrared is the band of light we perceive as heat. We cannot see this band of light with the naked eye, but we can feel this type of light in the form of heat. Our sun produces most of its energy output in the infrared segment of the spectrum. Infrared rays heat your body without having to heat the air in-between, through a process called conversion. The infrared is divided into 3 segments by wavelengths, measured in microns; 0.76~1.5 microns-near; 1.5~5.6 microns-middle; 5. See similar questions...

Takagi Water Heaters run on either Natural Gas or Liquid Propane. The internal computer, fan and igniter also require electricity from a standard electricity outlet. When you open a water faucet, the computer senses the water flow and measures the water temperature, it then turns on a power fan, an igniter and then the gas. The computer then adjusts the heat level to your desired temperature. The computer also checks the outgoing water temperature to ensure accuracy. See similar questions...

Biodiesel is 100% compatible with diesel #2, also known as heating oil #2, or more simply as diesel. If your heater is designed to run on heating oil #2, then it can run on B100 just fine. Kerosene, which is called diesel #1 or heating oil #1 and is thinner than diesel #2, requires experimentation. In general, if a heater is designed specifically for kerosene, then it can work with some kind of biodiesel blend (the blend being a low percentage of biodiesel and higher percentage of kerosene). See similar questions...

All Far Infrared products contain ceramic impregnated fibers that absorb ambient Far Infrared rays and then radiate this natural energy back into the body's tissues, promoting and improving blood circulation. The wearer does not often feel the thermal energy produced so the products can be comfortably worn all the year round. YES. See similar questions...

If you have the Acer Upgrade DVD, please install the infrared driver manually. It is under the folder "Common Driver\FIRQ" of the DVD. Please run FIRQ.reg to complete the installation. If you don’t have the Acer Upgrade DVD, go to http://global.acer.com/support/winvista/ to download the driver first, and then run the driver manually. This usually happens if the Launch Manager is not installed properly. See similar questions...