Call us with your Assessor's Parcel Number and we can look this up for you. (If you don't know your APN, visit our online Interactive GIS service.) A County-wide Snow Load Table is also available HERE.

Every Crown building is engineered to comply with regional building codes, wind load and snow load requirements. See similar questions...

Answer: With standard 2"x4" rafters the snow load is 30lbs. With optional 2"x6" rafters the snow load is increased to 50lbs. The wind load with standard 25 year asphalt shingles is 60 mph, with 30 year shingles - 90 mph, and metal roof - 110 mph. See similar questions...

Answer: The load capacity is roughly 1,100 lbs. We have seen them with as much as 23" of snow. Never the less, we do recommend that you brush the snow off the roof whenever it gets over a foot. See similar questions...

While no specific load ratings are available, this style of dome roof has been manufactured for more than 50 years. Hundreds of domes have been installed in heavy snow country, such as upper Minnesota and Quebec. In high wind areas, we recommend and have available inconspicuous wind reinforcing rings. See similar questions...

was the driest year of the three previous runnings, and there were short snowbanks to cross over most of the major passes, with a substantial amount (thigh deep) below Virginus Pass. In '95 almost the entire course was under snow, and the run was cancelled because of it. Expect anything in between. We'll post periodic snow reports here, as the season progresses. You can also check them yourself. There are unseasonable bare spots on the peaks above Silverton. See similar questions...

In New England, Colorado, Utah and Canada, snow chains are not permitted. All rented vehicles in California can be supplied with snow chains, which can be bought for $35 ($27 credit return if unused). Chains are required for famous "dumps" of snow and high passes with "Drive with Care" conditions. See similar questions...

We've have never experienced a problem during Wisconsin winters, however there is a possibility it could occur during a very heavy snow load. In order to prevent it from collapsing, a temporary "T" brace made out of 2X2's or similar should work on the 4X4 single blynd. You want to be able to wedge it in place from the floor to the roof. The 4X8 double wide will need 2 supports on the inside perimeter. There is a metal roof support in the middle. See similar questions...

The frame can handle a distributed snow load of approximate. 75 pounds. We recommend that you clean the snow off if it is wet and heavy with water. See similar questions...

This will vary. Please contact us for any special requirements you may have. With most of our products we are able to meet any wind or snow loads required. See similar questions...

There are four design loads in Larimer County. For elevations under 7000 feet the ground snow load is 30 pounds per square foot (psf). Elevations from 7001 feet to 7999 feet the ground snow is 40 psf. From 8000 feet to 8999 feet the ground snow is 50 psf. For elevations 9000 feet and over the ground snow load is 70 psf. The minimum basic wind speed is 100 mph (3 second gust) and exposure "C" will be assumed. Frost depth for this region is assumed to be 30 inches minimum. See similar questions...

You would be surprised how often we get this question (I had this question myself the first time I used the AdTool). Fortunately the solution is simple. When you have created your project, it will appear in the box that has all of your created projects. Before you can load the project, you must first click on the project you want to load to highlight it before you click the "load project" button. Once highlighted, click "load project" and it will load properly. See similar questions...

Just add the power requirements for all the equipment being powered, these details will be in the datasheet for the product under power supply. Then follow the steps described in the APS Configurator on the website. It couldn't be easier. See similar questions...

This answer varies a great deal all across the United States. One way to get a better idea of what these requirements are is to click here to enter your dealer's or factory-direct rep's eBuildings pricing website. Each eBuilding is displayed at the known minimum snow and wind loads (defaulted to "code" type buildings) for the zipcode you enter! Otherwise, it's best to consult with your local Lester dealer or factory-direct representative to determine the load requirements for your specific area. See similar questions...

The optimum 45 degree roof slope sheds snow in the winter, and can withstand a snow load of 18 pounds per square foot. See similar questions...

be rejected or a handling/disposal charge may be assessed if it is accepted. "Excessively wet" means more than 10% of the load is wet, and "frozen" means See similar questions...

No. To our knowledge there is no single place to go for that information. Check with your local building official for basic snow load requirements in your specific area. Once you have that information though, our Loads software will calculate unbalanced, and slope-reduced unbalanced snow loads. See similar questions...

The optimum 45 degree roof slope sheds snow in the winter, and can withstand a snow load of 18 pounds per square foot. See similar questions...