The scanner hardware has failed. Please ring our Helpline on 0800 373148, who will arrange for a replacement scanner to be sent to you.

The flashing red light indicates the batteries are low. Please ring our Helpline on 0800 373148, who will arrange for a replacement scanner to be sent to you. ACNielsen I-Scan has set the sound to be ON at all times. If you do find your scanner is not making any noise but scanning with the red laser, it is most likely the sound has been turned off by mistake. Press and hold "+" for 10 seconds until the 'LED Indicator' turns solid amber and a double beep tone is heard. See similar questions...

Jammed paper or a foreign object is blocking print head movement. Turn off the printer, press the adjust lever down to the lowest position, and pull out the jammed paper. Open the cover and remove any jammed or torn paper, or foreign objects. Then do one of the following: Sheet Feeder: Return the adjust lever to the position. Turn on the printer, reload paper, and press the paper button. See similar questions...

If a red ink light is flashing, it is installed in the wrong slot or is not compatible with the printer. If the power light is off, the paper light is flashing, and all the red ink lights are flashing, make sure the cutter is installed correctly. Press the paper button to clear the error. If the Power and Paper lights are flashing, and the red Ink lights are off, the cutter has a paper jam. Turn off the printer, remove any jammed paper, and turn the printer back on. See similar questions...

One of the ink cartridges is low. Make sure you have a replacement cartridge. To determine which cartridge is low, check the ink level. See similar questions...

The adjust lever is set incorrectly. Make sure the adjust lever is in the correct position for your paper. See similar questions...

First you will need to turn stove completely off and then back on to reset the board. and then go to your Owners Manual and begin the Start-Up Procedures. See similar questions...

The printer may have a maintenance request error condition. Turn off the printer, wait a few seconds, and turn it on again. If the lights are still flashing, contact your dealer or EPSON. See similar questions...

The printer is receiving a print job, replacing an ink cartridge, charging ink, or cleaning the print head. See similar questions...

The temperature display in the system tray will flash red if a severe weather alert has been issued for your location. It will continue to blink until you have read the alert. Once you have read the alert, the icon will continue to be red so long as the alert is in effect. The icon will change to blue once the alert has expired. To fix this, you must remove the temporary Internet Explorer files, click on the Internet Explorer button in the quick launch tray next to the "Start" button. See similar questions...

Your Xbox has an internal problem, and will need to be repaired. Please continue to the bottom of the page to the section on getting official Xbox support. See similar questions...

Answer: The flashing red LED charging light means that there is a problem with charging the unit. Most likely caused by bad contact between PMP unit and the battery. This means that repair work is needed to fix the battery contact. All Mp4 products carry 6 month warranty (or otherwise stated); 5 year warranty for Seagate HDD; 3 year warranty for other hard disk. See similar questions...

Your Hi Limit Safety Sensor is the cause of the green light flashing. This is due to the fact if the unit gets too hot and stayes there the safety switch will shut the unit down. Let the unit cool and then restart. See similar questions...

This flashing pattern indicates you do not have the AV cable in the rear of your Xbox connected properly, shut off your Xbox, reconnect it and try again. See similar questions...

Your controller is receiving power from the power pack but is not receiving a signal from the gameport. Shut down and reset the connection. Assure you are not using extension cables or switches and that your gameport is properly configured. Also make sure the MIDI set you are using is the default set for your soundcard. The MS FF controllers use MIDI signals to transfer information. If the proper MIDI set is not used the controller will not function properly. See similar questions...

The On/Off light flashes when approximately four hours of battery life remain. This indicates when to recharge the battery. For more information, see Charging and installing the battery. See similar questions...

A: Well, of course, we think our software is superior. The software you're referring to is a trend following system that costs about $4,000. It uses red and green lights and some kind of momentum chart to tell you when to trade. The DecisionBar software, on the other hand, is multi-faceted. It looks for trends, breakouts, and reversals and costs much less. DecisionBar trading signals are unambiguous and posted in real time. Once a signal is posted on the chart, it stays on the chart. See similar questions...

Yes, jars in amber, cornflower blue, olive green, etc. are worth more because fewer of them were made and they are in great demand by collectors. The amber jars were made that way as an attempt to keep fruit from turning brown. The amber glass kept out the harmful effect of light rays on the contents of the jar. However, the jars were less popular with homemakers because the contents were more difficult to see. See similar questions...

According to 3rd party research, blue light between 405-420nm kills the bacteria while red light in between 655nm-665nm influences the growth of new cells. This is designed to destroy acne and repair cells which were damaged by the inflammation and bacteria. Some customers have requested special all red Acnelamp units to treat Acne Rosacea. Other customers have used it to reduce facial wrinkles. Some customers even claim to have used red light to treat cuts and wounds. See similar questions...