There is no way that we can prevent oil from dripping on concrete pavers. Yet, because pavers are more dense than regular poured concrete, they will be easier to clean if the stain is cleaned soon after it happens. If you are working around your paver patio, walkway, or driveway with paint, cement, or mortar and should accidentally spill this on your paver surface, you should clean it off right away before it has a chance to dry. Otherwise, it will stain your pavers.

We use an extremely durable epoxy that penetrates deep filling up the micro pores. It also creates a tin layer above the concrete to protect against lemon juice, soda spills and other acidic products. This creates a satin finish that is soft to the touch and stain resistant.

Techni-Seal's Dirt and Grease Cleaner is recommended by manufacturers. There are also other similar products that will work too.

StreetPrint? can be installed very quickly with relatively little disruption, so it is usually much less costly and disruptive than concrete alternatives. StreetPrint? uses asphalt as its base. Asphalt is a flexible surface that is more likely to accept shifting due to weather extremes and can resist cracking commonly associated with other paving systems. Vehicle braking/accelerating and steering will not shift or break StreetPrint?, as often happens with brick pavers.

Concrete is an inexpensive and durable option, but it will crack. Pavers are more expensive but last longer, provide more of an interest from a design perspective, and are easily repaired if earth shifting occurs. Stone creates a beautiful and natural look but is the most expensive option. Many stone applications can be sandset, which is flexible to ground shifting. Occasionally stone requires a mortar setting, which is less tolerant of ground shifting.

In Europe, they have seen pavers last over 50 years. This is much longer than other pavements under normal residential use.

The joints between pavers eliminate cracking that is normal to conventional asphalt and concrete pavements. Yes, if necessary. That is an item we will discuss with you when we come out to give you an estimate.

You will never see a crack running through a paver patio or across a paver walk, and of course pavers offer more design diversity. Back to top

Concrete pavers offer more design options (more colors and sizes), whereas clay pavers offer less maintenance. The cost is about the same. Concrete pavers tend to lay a bit snugger, making tighter joints and a more consistently flat surface. Clay pavers however hold their color much the use of chemical sealers. Although the concrete is died straight through the paver, the die still has a tendency to wash off the top over time.

Sealing is not essential in many applications but it offers some benefits like making spills and stains easier to remove. Liquid sealers are applied after the pavers are installed and are cleaned. Once applied, the sealers soak into the concrete and into the joints. The sealers in the joints help keep the joint sand in place and prevent weeds and ants, and sealers are essential for areas around swimming pools.

For non-vehicular applications such as embankment stabilization, the maximum slope is determined by the angle of repose of the bedding sand, typically around 35 to 38 degrees. For vehicular traffic, the highest slope in use is 18% (about 10 degrees) in a street in Colma, California. Special consideration is given to the drainage of the bedding sand at the bottom of the slope.

We seal all of our countertops to ensure water and stain resistance. But this does not mean that they are totally stain proof. Acidic substances such as lemon juice, vinegar, or red wine should not be left on the countertop for more than several hours if spilled to avoid staining. Cutting directly on the countertops or placing extremely hot pots on the countertops may compromise the sealer allowing liquids to seep in and stain the concrete.

Our concrete is a composite product. It is harder and stronger than regular concrete and is sealed in order to prevent staining. We recommend cleaning any spills as soon as possible from the concrete countertops. Sealing concrete countertops is recommended annually.

Pavers can be plowed or shoveled just like concrete or asphalt flooring. Do not chop or use sharp objects to break away any ice on the surface of your paved surface. Although salt will not damage your pavers, non-corrosive de-icing products are recommended

Absolutely! 12"-18" of compacted base material is recommended for residential driveways. A standard 2-3/8 thick paver can be used for light vehicular (cars and pickup truck) applications. A Colonial random pattern is most popular in these situations.

There is no problem with using pavers around trees. You should consider leaving a 4-foot area between the tree and the pavers. Consult your local landscaper for these recommendations.

Yes, you can put pavers over concrete. There can be cracks in the old patio as long as it is still level and has not "heaved" up in any areas. Concrete makes a great base for our products. We will still need to retain the border of your project.

Depending on several things like temperature and humidity, with few exceptions, stains and sealers require a 30 to 45 day cure time. Concrete hydrates during cure. As it cures moisture dissipates from the slab. If it is sealed too soon the water vapors may build up and push the stain and sealer off. How soon a pattern can be engraved or cut also depends on several things like temperature, humidity, aggregate type, and the type of cut. You should wait at least 7 days before decorative engraving.

Yes, it requires a Zoning Permit ($75) to determine impervious coverage restrictions for the zoning district you are located in.