Solution: Use smaller pieces of wood and place them to allow proper air circulation between the logs. The same weight of wood cut in many small pieces will produce more heat than fewer, larger logs. Only add big logs when you have a good bed of red embers. Logs with a diameter exceeding 6 inches (153 mm) should always be split. Avoid stacking logs to the top of the fireplace. Solution #1: In many cases, a weak draft is simply due to insufficient heat in the exhaust system.

When biomass is burned, it produces heat (as in any simple fireplace or furnace). In most power plants (steam-cycle or steam-turbine systems), this heat is captured by boiling water to generate steam, which turns turbines and drives generators that convert the energy into electricity. New technologies now being evaluated include several types of biomass gasifiers in which biomass is heated to convert it into a gas.

AXTRO® is capable of heating areas above 260 square meters (buildings constructed to regulation 10/91) with any number or type of radiator installed.

Solution: Gradually close the air control mechanism in order to keep the flue temperature within the comfort zone, between 250 and 475oF (150 to 250oC). If you do not have a chimney thermometer and would like to get one, visit your local Osburn dealer. Solution: Replace the gasket using a genuine OSBURN adhesive and gasket kit. Please consult our accessories sections. Solution: Put less wood into the fireplace. The fireplace will not produce as much heat and will not heat as long.

InFlame Fireplaces have a heat output of up to 9000BTUs/hr depending on the fireplace. This is guaranteed to bring ample warmth to any room in your home. A typical electric fireplace offers from 1500 to 5000 BTUs/hr (approximately.) so our entry level 6000 BTU/hr max. output fireplace will provide you with a great heat supplement.

First of all, the Cherry-Pit-Pac is much safer to use. It is non-electric, so there is no danger of electricity next to the body. It stays warm for the amount of time most health care professionals recommend, approximately 20-30 minutes. Because the cherry pits cool off after that amount, there is no danger of falling asleep and getting burned. The other important difference is that it is portable. You don't have to find electric outlets, worry about extension cords, or stay in one spot.

All electric heaters except heat pumps are 100% efficient in converting electricity to heat. Heat pumps have an efficiency of 200% or more. However, different kinds of electric heaters are less effective in making the heat they product go to where it's wanted. Baseboard heaters are arguable the worst at distributing their heat, and floor type radiant systems are probably the best. For more information you may download our brochure entitled "Purchasing a Heat Pump".

There are a few precautions to take before implementing this TV application. First, take a thermometer and tape it to the wall above the mantel (where the plasma TV will be placed). Then and build a fire, let it roar while. Check the thermometer. If the temperature is above 90 degrees then the area is receiving too much heat - either escaping from the front of the fireplace and rising up the face, or radiating through the chimney to warm the outside wall.

Whether or not it makes economic sense to replace an electric furnace with a gas furnace depends on a lot of factors:

There are two systems in the AXTRO® Hydronic fireplace range. The first, is a copper coil immersed in the water within the main heating heat exchanger. The second is a separate external finned heat exchanger, guaranteeing a greater amount of hot water and easier maintenance.

Yes. Aside from the fact that all of our fireplaces radiate heat from their fronts, there is still heat that can be withdrawn from the fireplace. Using the blower increases the airflow thereby maximizing the heat being conducted from the back side of the fireplace. Adding a fan is easily done if 110 power is hooked up to the electrical box inside the unit. If power is not already at the fireplace, it still may be possible but may be more costly.

More so. A Bellfires? will provide ample heat without the grills and fans. The special refractory material of the Rosin Design radiates a comfortable warmth into the room. This type of system has been used in Europe for over 65 years.

The product can not be installed in any area where its temperature could exceed 120?F. Solid wood moldings or trim may be used to buffer the product in these areas.

Extremely low frequencies (ELF) are from 0 to 300Hz, and include those arising from power lines, which are at 50/60 Hz. They also originate from electrical wiring in buildings and from electrical appliances. Radiofrequencies (RF) are in the range 30 kHz to 300 GHz. Mobile phones operate in the approximate range of 800 MHz to 2GHz. These differences in frequencies result in very different interactions with tissues. Strong ELF fields can cause nerve and muscle cell stimulation.

Depending on the available sun shine the ecological payback is less then two years. Typical conversion rates of solar modules are 12 to 15%, meaning that 15% of the energy that falls onto the module’s surface area is converted into DC power. Even at 12% the overall energy generated by the cells over the expected life span of 50 years is a tiny fraction of the energy used to build all components of the system.

The heat pump is not working. The electric strip heat in the furnace is keeping the house comfortable. This heat costs 3 times more than heat pump heat. Many people do not realize in the winter that their heat pump is broken because the strip heat continues to keep the house comfortable. If you notice a little light on your thermostat is on, very often you had better check to make sure your outdoor unit is working.

No. Our solar power systems are designed to provide electricity to run your lights, appliances and other electric devices in your home. Other solar technologies are designed to turn the sun’s light into heat instead of electricity.

There's no stored energy in this case, but the G3-60 can instantly feed back 10 to 4 kW; corresponding to 50% to 40% of the power required to sustain a continuous shower at 2.25 gpm. Similarly, an instant gas water heater's load will be reduced by 34,130 to 13,652 Btu/hr (0.341 to 0.137 therms). Without GFX, a tankless electric water heater demands 83 to 41.5 amps at 240 volts to sustain a 20 to 10 kW shower stream. With GFX, AC current demand drops by 41.5 to 24.

Yes, many of Foster's customers have added a heat pump to their existing oil, gas or electric furnace to cut heating expenses. You would then use your oil, gas or electric furnace as back-up heat, which in this climate, would be very infrequent. You could expect your oil bills to drop substantially.