For the greatest comfort and best indoor air quality in your home, set your humidistat between 30 and 40 percent humidity. At that level, health-endangering conditions (such as bacteria, viruses, fungi, mites, ozone production, etc.) are greatly reduced.

This website is designed for use with Netscape 5 (or higher), Internet Explorer 6 (or higher) and Firefox browsers, both on Macintoshs and PCs. However, since every browser displays the information provided a little bit differently, we do have preferences, and recommend Firefox. With Mozilla's Firefox browser you can use the keyboard to navigate through the quizzes with ease and speed. See similar questions...

There isn't such thing as a "perfect" dwell setting (if there were then it wouldn't be adjustable). Every marker operates a little differently and every marker requires a bit of tuning to perform well. Instructions for this and other tasks can be found on this website under the Adjusting & Maintaining pages. See similar questions...

The input sensitivity setting is a function of amplifier gain. You will want to match it with the output level of whatever is before the amp in the audio chain (i.e. preamps, mixers). For amplifiers with a 0.775V position, this positions corresponds to a 0 dBu level. The 1.4V position corresponds to a +4 dBu level. The 26 dB position is a fixed gain position. The 26 dB position is also the lowest gain position, and will usually work well with output levels of +10 dBu (2.5Vrms and above). See similar questions...

Most of our customers install the humidistat on the cold air return duct, about 1 to 2 feet above (upstream) of where the humidifier unit itself. In this location, the humidistat will measure the average blended humidity in the air returning from the whole home and control the humidifier on this basis. Alternately, the humidistat can be located anywhere else in your home that is convenient for you - for example, you may decide to mount it adjacent to you thermostat. See similar questions...

A typical home produces 22 pints of water vapor per day. Once this moisture rises to the attic it condenses. This condensation on your roof deck causes mold, mildew and rotting of the wood. The mold and mildew growing in your attic affects the quality of the air in your home. The rotting of your roof deck can cause thousands of dollars to repair. See similar questions...

When starting the game with one peasant only, full speed is best for a short while. After three or four buildings are completed, it is best to slow the game to one notch below that. This makes units more responsive, so it is possible to cast spells, react to attacks, and so forth. If the lag in a game is particularly bad, the speed should be slowed to about the midpoint to reduce the effect of the lag. Note that lag is caused almost entirely by network and modem performance. See similar questions...

There is no single best adjustment setting for your KONI shocks because every driver and vehicle has different preferences for comfort, performance, performance modifications and roads to drive on. For most vehicles, we suggest that new KONI's be installed in the full soft position (the standard setting right out of the box) to take advantage of the balance of ride comfort and handling designed by the KONI ride development engineers. See similar questions...

ADFSBuffers are Read Ahead and Write Behind buffers for ADFS on your Archimedes. These are designed to improve the speed of filing operations by doing work at optimum times. There are some side effects of using them though. When active under RISC OS v2.00 and v2.01 discs must be dismounted before being removed from the floppy drive. Failure to do so results in the dreaded 'FileCore in use.' error. See similar questions...

The ideal setting depends upon the vehicle, and the driver’s tastes. Settings tend to be different on rear wheel drive cars than on front wheel drive cars. Also, settings will vary between drag racing and road performance environments. Test the different adjustments to find the best combination for your vehicle. See similar questions...

Don't find the question you are looking for? Send an email to support@ultimatebalance.com. We'd like to hear from you! The Trainer should be fully charged before using it for the first time. The Power button should be held down until the voice feedback says "Welcome to Ultimate Balance". See similar questions...

To create an atmosphere that is friendly and comfortable, a home setting works well. You need to have a place where everyone can sit comfortably and see and hear each other. If your home will not work, see if another couple in the group would be willing to offer their home as your group's meeting place. See similar questions...

Saxony: It has a luxuriously smooth and soft finish and shows subtle highlights and accents. View our great selection of high quality carpets here. See similar questions...

Turn up the volume to a slightly higher level than you would normally use for comfortable music-listening. You want to ensure that the only stimulus your mind has is the sound waves coming in through your ears. See similar questions...

Here you may select the mode how your host application (where the scan finally goes to) should display that image. automatic" = the internal color space used by the host program should be used for this image, too. In this case you must specify under "Internal" what color space is used. See similar questions...

Stock settings on the 4th gens are around 43 to 45 psi. The best (adjusted) pressure seems to be variable depending on your cars specific modifications. But even cars with similar mods react differently to pressure adjustments. Some people claim 47 to 49 psi is best, while others find a lower setting like 39 to 42 psi is best. From testing, it seems the computer will adjust itself to a fuel mix level it is comfortable with. See similar questions...

The humidistat will help prevent the problems of having too much humidity in the air. The humidistat is wired in series with the 24-volt power supply of the TM-2000 and will prevent the TM-2000 from operating if the humidity level exceeds the setting on the humidistat. See similar questions...