You can connect a second display to a Kaleidescape Movie Player or Movie Player 2. The Player normally sends video to all video outputs but they cannot be controlled independently. The settings you make for the Primary Video Output in the Installer Web Utility apply to all video outputs. For example, if you set the Primary Video Output to match a 16?9 display and a secondary video output is connected to a 4?3 display, the image on the 4?3 display will be distorted accordingly.

Yes. To interface a TIMS unit to a Modality without any extra video outputs requires the use of an active video splitter. (A video splitter is a "one in, two out" device.) You would disconnect an existing video interface on the Modality, attach the video splitter, connect both the TIMS unit and the original video interface to the outputs of the video splitter. Do not use a "T" connector in lieu of an active video splitter, for the image will noticeably degrade.

This can be configured in the "MediaPortal Configuration" program where in the "General" part screen selection can be enabled by selecting "use screenselector" and setting the appropriate screen in the selection box afterwards. the moment there are no media extenders that work with MediaPortal. As a developer you are more than welcome to add support for those. This depends on your remote control.

Subtitles can only be placed on top of the video. Placing the subtitles below the original video is possible by enlarging the video frame. This is done by adding black bars to the top and bottom of the video. These black bars will be visible when the video is not in fullscreen. They are different from black bars that are only visible during fullscreen playback. Those are not part of the video frame and thus can not be used to put the subtitles onto.

The bandwidth of the Model 990?s relay controlled, three input/one output component video switch is in excess of 100MHz. As we have stated in the past, we feel that analog video bandwidth above that level is neither useful or advisable.

I put a disc in my player and I get a screen that says smart navi or the songs have question marks next to them.

The TV SCART provides Component video, Composite video and RGB. The VCR SCART provides component video with RGB pass-through. There's also an S-Video connector, and a Composite video output.

On a Dry Mount charger, you will need to jumper the unused positive terminals to one of the positive terminals that you are using so that the charger will "read" a battery on each lead.

Yes. Your music library can be browsed, selected, and played back using a stand-alone interactive touch panel. You can view information about their music on these touch panels, navigate lists, and select music to play, all without the use of the onscreen display. The bi-directional Kaleidescape Control System Protocol can supply music information fields to a touch panel or other devices with data display capabilities.

If there is no activity on the 935 screen, then as far as the 935 goes there has not been an attempt to communicate with it. See Remote-Com.jpg for an example of what the screen might look like after the hardware search program has completed its update. The user must click on the UPDATE command button in the Hardware search program. See the attached file Remote-NoCom.jpg for what the blank screen looks like if the 935 does NOT receive any communications.

To set up your system for dual video, connect your computer to a projector or TV. With all equipment turned on, Right click on your Windows? Desktop, and select "Properties". Select the "Settings" tab. On the control screen you should see two "virtual monitors", labeled 1 & 2. Select 2. (If you do not see 2 monitors listed, please consult the Hardware Guide) Near the bottom of the window, you will find a check box labeled "Extend My Windows Desktop onto this Monitor"; check it. Select "OK".

Your list of videos will be displayed, click on the plus sign next to the video that you would like the code for. The plus sign will expand to show four different types of code: URL, Popup link, normal link, and Iframe link. Most users will use option #1: URL. By copying and pasting the URL link into your email message, others will be able to view your video simply by clicking the link in their email message. The other three options are used for adding code to your website.

Answer:The output mode has likely been changed from normal to VGA (computer monitor.) To restore video, there is a button on your remote labeled V-Mode. Press this a few times and your video should restore. If not, contact RSQ via phone for assistance in performing a reset. Answer:You are likely using the Red Green Blue (component) outputs from the player and you have not changed the video mode yet. Go into the setup and change the video mode to one of the other selections (not VGA.

DVD subtitle is available by default. Press SUBTITLE button to switch between different subtitle tracks. To display subtitle with a media file playback, you need to have VSFilter installed, and a subtitle file available to be displayed. Use SUBTITLE button to switch between subtitle tracks. Subtitle also works for OGM and MKV containers. Make sure you have DirectX9(c) installed, and the latest service pack for your Windows OS installed (SP2 for Windows XP).

If you have found an interesting video on YouTube which would complement your article, please add a reference to it at the very start of the article text in comment tags, for example: [c]pls use this youtube video: abcd1234[/c]. We will consider the video as part of the review process.

Analog video transfer can be done by Composite & S-Video. HD video transfer can be done by Component (Y/Pb/Pr). You need a part called a Transcoder. This converts 3-wire Component to 5-wire RGB/HV or VGA (15-pin). These can be purchased online for about $150. *See the TV list at the end of this article.

Both you and the other camera or you and the other user. There can be any # of people/images on the video feed but only 2 connected cameras during a video chat session.

Some of the layout engines such as Swing and PDF use Java Font objects. In order to answer some questions about fonts (for example, what is this font's descent), the code needs a FontMetrics object. To get a FontMetrics object, you need a graphics context, which DataVision gets by creating an AWT Panel object. That's probably what is trying to connect to the display.

Yes. Every CD-i player from Philips is equiped with a serial port, either as mini-DIN connector at the back of the player, or it can be made available by connecting a port splitter to the input port of CD-i players with only one input port (like CDI 450, CDI 550 and FW380i). On players with only one port for input devices at the front and one at the back, this port at the back can also be used as a serial port.

Most modern displays offer S-Video connections over at least one of the SCART sockets, however there is no guarantee of S-Video signal support, try it or look in you displays manual.