For our Canadian customers and customers in Montana, USA, parts and service are provided by our exclusive Canadian Distributor, "WLT DISTRIBUTORS INC" a company based in Winnipeg, Canada. As for our international customers, parts and service can be obtained by contacting their local distributor or by calling our Customers Service in Montreal at 514-339-9355.

Fuel injection is a replacement for the carburetors that were around since the dawn of the automobile. There are many basic types of fuel injection, but we should start by saying what a fuel injector is - it's basically an atomizer, something that sprays a mist of gasoline into the air. This helps the gas to mix better with the air and stay in an even suspension, so that it burns more evenly and creates less pollution and more power. (Think of cooking spray vs.

We have most spare parts available, however if they have to come from interstate it may take a few days.

Frequently used maintenance parts (air and water filters) can be shipped within 24 hours, other spare parts can be shipped within 3 days. However, we require that each country or regional distributor to have a minimum level of inventory for those parts in his possession. The water generation capacity is guaranteed for the design conditions. For all other conditions, it is guaranteed that the unit performs as described in the manual.

Yes. All spare parts for the Challenger are held in stock. Orders are same-day despatched by mail or special delivery.

Edelbrock and Accel have multi-port fuel injection (MPFI) systems, however the Accel must be tuned with a laptop PC. These are quite expensive though. Force Fuel Engineering in Florida can handle a conversion if you send them your manifold. They recommend an open plenum manifold, but they can do 180 degree manifolds, too.

NBB maintains the largest library of Bioheat® fuel and Biodiesel information in the world. Most questions can be answered through a review of the information on the National Biodiesel Board website located www.biodiesel.org. If further information is desired, you can email your question to the NBB at info@biodiesel.org.

Answer: We have a large stock of consumables and spare parts at our warehouse. To ensure that your equipment serves out its entire life span we recommend that you buy only original and Xerox spare parts and consumables from our authorised dealers.

your physician, I am always available to consult with you, either by phone, email or in person. I see patients by appointment, and make home visits in special circumstances. Please feel free to call or e-mail me with any questions about treatment, fees and to discuss your particular situation.

There are long waterless stretches but the guidebooks list all known water sources so you know how much to carry. All water should be treated or filtered. Visit the Water Purification section of this site for more information.

There are ATM machines around, some resorts have them, but they are mostly in the cities and towns, not the resort areas, so don't rely on this as your only source of cash. A number of hotels in the DR have casinos with slot machines, table games, etc. Suggest you use U.S. currency to gamble with - if you play with U.S. money any winnings will be paid in U.S. currency. If you use Dominican Pesos, winnings will be paid in Dominican Pesos.

Fuel injected engines are self adjusting, automatically idle themselves back when the lubricant is improved with Tufoil, just as the carburetor would have done.

We still enjoy working with the Carbureted setups, they also have a more traditional look to them as well. Easy to tune and less complex. We do provide a Fuel injected setups with the complete Throttle Body, injectors, fuel Rail, wiring harness, computer and sensors to plug in. The EFI Mass Flo setup is an easier way of going. Figure Approx. another $2,000-$2,500 over and above a Carbureted setup. It's recommended that you have technical knowledge on Fuel Injection when dialing in the engine.

Fuel injection is not necessarily any more complicated than a carburetor. It may seem more complicated to a novice fuel injection enthusiast, but in reality, carburetors can be more complex. A typical Holley carburetor has over 120 possible adjustments. A stock TPI intake has only three items which can be adjusted, both of which are on the throttle body (throttle position sensor, idle air control valve, and minimum air screw).

Besides throttle bodies, linkage and manifold (if required) typical components are; A management system , wiring loom, fuel pump, fuel pressure regulator, fuel injectors, appropriate plumbing, air horns and a ducting/filtration system for the incoming air.

There are many benefits. The quantity of dirt in your vehicles fuel injectors and carbon deposits in your engine's pistons and valves impacts how noticeable these benefits are. Benefits include:

A - Professors at Messiah are accessible to the students, and they have office hours for students to be able to contact them. back to top

Currently there is a shortage of Medical Laboratory Scientists, so there are more jobs than qualified applicants to fill the positions. On the average, recent graduates have had several job offers with good starting salaries and benefit packages. Labs in the Maine/New Hampshire/Massachusetts area offer starting salaries anywhere from $25,000 to $38,000.

There are several casting agencies that can supply hundreds of extras a day. The cost of an extra is usually Lm25 per day (approx US$63 or Eur58). Casting agents can source large numbers of extras, as well as secondary-role actors. The Maltese are essentially Mediterranean in appearance, but a large diversity of Caucasian and Southern Mediterranean looks are also found.