The default configuration is to activate the Windows 98 auto-suspend feature if left idle for 10 minutes when running off internal batteries or 1 hour when docked or connected to the vehicle battery.

When the site times out I have to start over at the Home Page and re-enter my user name and password information. Why does the server time out?) In order to save server resources, the server is set to time out after 12 minutes of inactivity. The reason for setting a timeout is to keep the server from getting bogged down and inaccessible. See similar questions...

No, Time Out automatically pauses the breaks when you aren't using your computer. So when the screensaver is active, or the computer is otherwise sitting there without being used, Time Out won't do anything. When you return to your Mac, if you've been away for longer than the interval set in the preferences, Time Out will reset the break timers, so the next breaks will be the full work interval from that time. You can change this amount or disable this feature in the preferences. See similar questions...

USP–NF Online requires user authentication. Unless you select the automatic login option you will need to login every time you attempt to access USP–NF Online. You will also need to reenter your username and password if you leave the session inactive for an extended period of time. See similar questions...

On older engines, it is not at all unusual for the idle speed to increase when Tufoil is used. If the engine block has warped or has serious internal friction problems, the improvement with Tufoil can be quite dramatic. It will be less noticeable in loose engines that are in tip-top shape. You can literally "double the life of your engine" by using Tufoil regularly! Most people consider 100,000 miles normal for their car. See similar questions...

a rule, EFI does smooth the idle and on some applications we have seen a smooth idle all the way down to 700 rpm. See similar questions...

Here's a way to figure it out-- on a cold morning, when you start your car it idles higher than normal right? That's because this valve is open letting more air in to idle the car up to it warms up faster. Now... if you sit there until it warms up, does the idle drop back down to normal all of a sudden? If so it's a FIDLE valve (two wires, ground and 12v+). Or does it slowly idle back down to normal a little at a time? If so it's either a PWM or stepper motor valve. See similar questions...

a security measure, your PBeBank.com Internet Banking session will be automatically terminated if you leave your computer idle for more than 5 minutes. However, you must always ensure to properly logout after each Internet banking session. See similar questions...

Rate yourself 1-5 on technical confidence in yourself. 1 being "I can't paint by numbers" and 5 being "I can probably build a car from scratch if I have the right documentation, and I'm resourceful enough to do some research and find some of my own answers. See similar questions...

Although first generation Probes were known for very mild vibration, excessive vibration is common among older Probes. Although this can be a result of a crack somewhere in the intake duct work or uneven compression in the cylinders, it's often caused by cracked or broken motor mounts. Probe motor mounts are very prone to failure after 75,000 miles. See similar questions...

FirstSpot®'s idle timeout handling is both efficient and accurate. It will only timeout users if they are idle (i.e. no network traffic) for a specific amount of time. Also, there are no "keep alive" packets sent from browser to FirstSpot® (which will degrade network performance). See similar questions...

No, the UV system should be left on whether you are using the water or not. The lamps age regardless of the amount of the water drawn through the system. By leaving the unit on, you will eliminate the potential problem of having contamination pass through the system while the unit is off. See similar questions...

Your idle speed adjustment screw is incorrectly tuned. When you apply full brakes, the carburetor opening must not be completely shut off. To adjust the engine's idle speed, see the engine tuning sheet that came with the engine or your kit. Click here if you have lost this tuning sheet. If adjusting the idle stop screw does not solve the problem, see below. See similar questions...

The shut-down controller is controlled by monitoring the switched 12V line. When power is cut from the switched line (turning off your ignition) the shutdown controller sends an ATX pulse to the operating system to initiate your chosen shutdown mode(shutdown, hibernate, standby).[ Back to Top ] See similar questions...

The transmitter is shut off as a safety measure and to save battery power. It prevents the inadvertent commanding of the system when the operator is not in attendance See similar questions...

Pericom PLL automatically shuts down when the input clock is from several MHz to 20MHz. The actual values depend on the specific product. Lower frequencies will results in higher jitter. Please check with the datasheet or contact technical support http://www.pericom.com/contact See similar questions...

By design, the VeaLink system does not require manual shut down when exiting the vehicle. Users set their system to go into standby, hibernation, or shutdown depending on their preference. Upon reentry, the VeaLink system is ready for use within 10 seconds of turning on your vehicle’s ignition. See similar questions...

Text messaging works much like voicemail in this regard. If the phone is off, the message will be stored in your mobile inbox. When the phone is turned on, you will see a new text message waiting. See similar questions...

The CD should kick-off the installation when the CD is retracted into the drive. Windows 98 does not always acknowledge the CD drive unless the PTU is booted up while in the docking station. Let the PTU fully boot to the 16-pin selection screen and then cycle the CD tray out and back in. This sometimes requires a couple of attempts before Windows recognizes the auto run file on the CD and begins the installation. See similar questions...