Recommended loads are as follows: 20 gauge -- 65 grains of FFG black powder and 1 ounce of shot, 12 gauge -- 75 grains of FFG black powder and 1 1/8 ounces of shot, and 10 gauge -- 85 grains of FFG black powder and 1 1/4 ounces of shot. Dixie stocks all of the wads needed in assorted gauges. Muzzleloading shotguns can be loaded with patched round balls as well as shot. We recommend using a .600 round ball for the 20 gauge, a .715 round ball for the 12 gauge and a .

You are allowed to bring 200 shells into Canada, shells are also available here. My preference in loads (all around) is a Game Bore 2 ½ inch # 6 which is a North American # 7, or what I will do is load a #8 followed by a 71/2 or 6, I only shot 1 oz loads out of my 12 and 16 gauge guns, and 7/8 oz. out of my 20. See similar questions...

There are certain items which are necessary for shooting and maintaining your muzzleloading firearm. The basic requirements are black powder ( or replica black powder), percussion caps or flints, adjustable powder measure, projectiles, patch material, short starter, lubricant, ramrod, cleaning jag, solvent and gun oil. In addition to these basic required items, there are certain accessories that can enhance the muzzleloading experience. See similar questions...

Muzzleloaders, by virtue of the fact that they do not fire fixed ammunition, are considered antique firearms under The Gun Control Act of 1968 and are not restricted in trade by any federal law or regulation. This applies to both antique and new made muzzleloaders. There may be state or local ordinances which restrict our ability to ship direct to the customer. Residents of HI, NJ, MA and MI are urged to check their state and local laws for any restrictions on ordering black powder firearms. See similar questions...

According to the administrative rules associated with the Wildlife Code, the definition for an unloaded muzzleloading firearm is as follows: "Removal of percussion cap or removal of prime powder from frizzen pan with frizzen open and hammer all the way down or removal of prime powder from flashpan and wheel un-wound or removal of prime powder and match with match not lit shall constitute an unloaded muzzleloading firearm." (17 Ill. Admin. Code, Sec 660. See similar questions...

Unless the police have good reason for not issuing one, then once a security cabinet has been installed & approved a license will be issued. See similar questions...

A shotgun start simply means that all players tee off at just about the same time. We don't actually use a shotgun to signal the start. This is possible because each foursome starts on a different hole. Usually, two groups are assigned to each hole, so not EVERY single group starts at the same moment. In this format, all of the players finish at about the same time (unless some groups are not keeping pace), which makes it nice if there is a group meal. See similar questions...

Shotgun stands for access to and familiarity with weapons (not only shotguns, but we needed an S). This is almost always a factor in workplace homicides, but, of course, is not required for non-lethal violence. The Triggering event is the last straw or that which causes the perpetrator to believe that there is no way out, no more options. See similar questions...

The best thing to do is go to the homepage and either use the search feature or left click on any of the categories at the top of the home page. If you're looking for a shotgun sight, click on Shotguns and so on. If you can't find what you are looking for go ahead and give us a call at 800-589-4315, as there are some models of sights that can be modified to fit guns that may not be listed on the site. See similar questions...

All weapons are banned from student housing, and failure to adhere to this directive will be branded as a material breach of contract, subject to eviction from student housing. See similar questions...

Please note - Shotgun chokes will vary the above dimensions at the muzzle depending on the choke restriction. See similar questions...

The Remington 1187 will operate most reliably with loads that are at least 2-3/4 dram, 1 1/8 ounce loads. A 3-dram, 1 1/8 ounce load is better. See similar questions...

We recommend replacing the magazine spring in your defense shotgun every 6 months if the shotgun is kept loaded. See similar questions...

The chrome plating of shotgun bores is done purely to give the highest level of protection against corrossion within the bore. [ back to top ] See similar questions...

The load can be anything you like. We hope you will be creative and make this event fun by having creative loads to carry. You might represent your country or your state or your sponsor or your favorite food or cartoon character in what you decide to carry with your lift. The important thing is that it is artistic and fun! See similar questions...

You can search the trace repository with your sequence using SSAHA or translated SSAHA. You can learn more about SSAHA here. See similar questions...

Most shotgun mics are phase shift hypercardioids at the bass end and line interference types at higher frequencies. Hypercardioid capsules with good LF response are difficult to make, and often it is desirable for their main application (dialogue pickup) to roll off the bass, so there won't be so much (a) room rumble and (b) handling noise as the mic is panned around. [dj] {41} See similar questions...

Many of the items are advertised at dealer prices. They require an FFL and in most cases a state tax certificate. Many others have minimiums that must be satisfied to fulfill an order. In some cases, you can buy at the quoted prices. Just read the fine print before you try to order. See similar questions...

Modern fuel injected engines are controlled by a sophisticated engine computer (ECU). The job of the ECU is to take in information from the driver and the environment, crunch the numbers, and calculate the load placed on the engine. This load information is sent to the fuel injectors in the form of a pulse width (length of time the fuel injector is held open) and a frequency (how often the fuel injector is opened). See similar questions...

Spring rate is the amount of force that is required to compress, extend, or twist a spring one inch. Usually spring rate is measured in pounds per inch. Load rate is a is the amount of weight the spring is designed to carry at a certain height. See similar questions...