This section was written by someone who wishes to remain anonymous, but I will field any questions on the subject -IDB] Yes. When two loads are connected in parallel (such as with a Y-cable) they get the same voltage as each other. They do NOT get the same voltage as if only one load was connected because the head-unit has an internal resistance (typically around 600 ohms).

The Acnelamp has three configurations depending on how far your acne is spread out. The single head unit is typically used for people that have acne on one spot. The two and three head are perfect for getting the sides of your face and front of your face at the same time. Each lamp has the same power per centimeter, but cover different areas. Having acne all over your face does not mean you absolutely need a three head lamp.

Each type of model comes with compact, sleek and modern aesthetic design and provides clean and healthy

No, there are several disadvantages to that. First of all maintenance becomes needlessly complex and you gain very little in this. In fact if your partitions are too big you will seek across larger areas than needed. This is a balance and dependent on the number of physical drives you have. To some degree, yes. Still, some directories should not be split off from root, check out the file system standards for more details.

MP3Car vBulletin 3.5 Standard ---- MP3Car vBulletin 3.5 2-Column ---- Kirsch vB 3.6.0 - Fluid ---- Mobile

Although it may work, the Cabbone is really not designed to do this. The electronics are designed for speaker loads, not low-level guitar signals and as such, you may encounter noise. Furthermore, there are no provisions for solving ground loop problems. The Radial Switchbone is an excellent AB-Y switcher designed specificaly for this job.

No, SoundSplinter is currently a subwoofer driver specialist only and does not carry pre-fabricated enclosures or amplifiers. However, we do provide recommendations for the basic enclosure constraints that should be implemented with each of our drivers, linked on each series' main product page.

To hook up a HSU Research subwoofer (any VTF or STF-3) to a pre-amp, a stereo pair of RCA cables are to be connected from the pre-amp line-level outputs to the subwoofer line-level inputs. This stereo pair output can be sourced from secondary line-level output jacks or by splitting the line-level output jacks by an (1 RCA male to 2 RCA female) adapter. This adapter can be found at Radio Shack.

Unplug the AC power cord from the outlet. Now hold the rear panel Default button in (you'll need a pencil, paper clip or similar long slender object) and reconnect the AC power cord to the outlet. Keep holding the button in, until the Output LEDs flash the "Knight Rider" pattern (from the outside LEDs towards the center), indicating the unit has been reset. If the unit will not reset with this method contact the factory for further information.

The CDU550 is provided with a system whereby by connecting both USB ends, the modem receives more power thereby extending its signal strength slightly. This is only really necessary in fringe coverage areas. Please see the manual for a complete guide to connecting your CDU550.

This unit is really packed tightly and just doesn't allow room for this. The performance would be seriously compromised, and because it's a double sided board a modification would take four or five hours if you really knew your way around inside the unit. Make sure that every SR 1L is set to its own address, using the DIP switches (earlier style) or Rotary selector on the side of the piece.

This depends on several things - price, power, weight, and, of course, personal taste. My feeling is that combos are good up to about 300 watts or so. Beyond that, they get to be too heavy to lug around, and too bulky to fit in the trunk - or even the back seat - of the average automobile (I'm assuming, of course, that you will be lugging your own gear around all by yourself).

A window unit is a self-contained packaged air conditioner. All components are housed within the unit. It is installed through an opening in the wall and no inter-piping connection is required. A single split, as it is called, comprises 2 parts that make up a system air conditioner: the outdoor unit (condenser) and indoor unit (Fan coil). The FCU is a cooling coil that cools the room, interconnection piping between the condenser and fan coil is required to run this system.

To provide more flexibility in configuring the system. Now, users may place the codec in a cart, or in a rack—whichever best suits their room needs.

A split system uses indoor and outdoor components to provide a complete home comfort system. A package unit or self-contained unit requires no external coils, air handlers, or heating units. Leave all interior doors open at least 2 inches if the room does not have its own return air intake vent. Have your heating and cooling system thoroughly cleaned and tuned (not just a check-up) by a reputable company with certified technicians, at least once or twice a year.

If a team is below the cap, then their Disabled Player, Bi-Annual, Mid-Level and/or Traded Player exceptions are added to their team salary, and the league treats the team as though they are over the cap. This is to prevent a loophole, in a manner similar to free agent amounts (see question numbers 29, 30, 31, 32). A team can't act like they're under the cap and sign free agents using cap room, and then use their Disabled Player, Bi-Annual, Mid-Level and/or Traded Player exceptions.

It's the most efficient way to create an active pickup. All the coil connections are shielded, the pre-amp is shielded, and the output of the pickup cable is low-impedence, which makes it less susceptible to noise. Also, it avoids a spider web of wires and possible loose connections in your guitar and the installation is simple. All the benefits with none of the hassle.

If you could prevent downloading, this would likely be a fair use. In fact, many software vendors will send you a time limited copy of software for this very purpose. Check with the vendor.

Rip and Tear Auto from the CRX Resource answers: The carb is a Weber 32/36 DGAV. This is the carb that is used in the single Weber conversion kit for carborated 1st gens. We had to change every jet in the thing. Right now it's got: It still needs a bigger secondary idle jet (don't have one yet) and I am still playing with the air correctors. The injector holes are just taped and plugged with standard brass plugs.