No, this can blow the filter material right out of the wire mesh and ruin the filter. Pick a nice day to clean the filter and let it dry naturally. A low pressure air flow such as from an industrial drying machine or blow dryer will help the filter dry more quickly.

A3: No Secomak's air knives are specifically designed for use with lower pressure high velocity air supply for optimum Performance.

You should not use more than one filter in any one place in the HVAC system due the air flow restriction it imposes on the HVAC system. Consult your service manual regarding specifications for your particular furnace or air conditioning system.

The air filter is a critical component of your engine. We cannot stress enough that for proper care of your engine, the air filter must be in proper working order. The air filter in all of our Nitro kits is pre-oiled for your convenience, however it must be cleaned and re-oiled after running 2-3 tanks of fuel. To clean the air filter, take the foam filter element out of the rubber boot and use fresh Nitro fuel to rinse the dirt from the foam element.

Yes we have. Too much nitrogen in air and it cools the cut to below combustion temperature. The oxygen is required to cause the iron to 'burn' (oxidize quickly) that's how you cut iron with oxy-fuel. The fuel gas heats up the iron to the ignition point, then the oxygen actually allows (a portion of) the steel to burn, creating the heat to melt the rest of the steel.

Yes. Any vacuum source that can pull 25"Hg will work. One pump that we recommend is the Rocker 300, available from LabDepot. An inexpensive pump that we have also rated is the Barnant Air Cadet Single-head pump, available from McMaster-Carr (#41675K41) as well as Fisher Scientific. Any small air compressor will provide enough pressure/volume to operate the microfluidic platform.One inexpensive commercial compressor we have used is the Black&Decker BDC4G four gallon compressor.

Yes, the air purifier kills germs and bacteria and destroys odors; but it does not dispose of the particulate, which is airborne. This requires a quality particulate filter.

The Audiosonic Acoustic Cleaners operate using normal plant compressed air provided three important factors exist. but remember the Audiosonic Acoustic Cleaner is only "sounded" for a few seconds over usually between every 3 - 30 minute period depending on the application.

If you require more than one outlet, order the first outlet at the appropriate rate from item "1. a." under "Description of Service" in our plumbing services form. Each additional outlet is to be ordered from item "b." This is based on the floor distribution for the additional outlets. Determine your CFM (cubic feet per minute) requirements and include this information. It can be located on the equipment itself.

The water is condensation. Humidity in the air being compressed is drawn into the air compressor along with the air. The higher the humidity the more moisture contained in the air. Compression causes heat, so as the air cools the moisture in the air forms condensation and collects in low points in the compressed air systems, such as the air receiver, airlines and/or airline drops. Some or most of the moisture can be removed with the use of aftercoolers, dryers and/or filters.

Although the FDA has no health-related standards, it does consider some portable air filtration systems to be Class II medical devices. In the United States, nothing can claim this status without FDA approval. To get approval, a manufacturer must show two things: (1) that the device is safe, usually indicated by the Underwriters Laboratory (UL) seal, and (2) that it has a medical benefit. Look for both the UL seal and a statement of the FDA's Class II approval.

To keep your furnace and air conditioner operating at peak efficiency. When the heat transfer surface of the furnace and air conditioner (indoor evaporator coil located on top of your furnace) gets covered in dirt (dust, etc...), it requires more energy to achieve the same load. For heating, this means you will consume more gas and electricity to heat your home, and for air conditioning, you would use more electricity to cool your home.

Look for the arrow showing airflow direction on the old air conditioner furnace filter and remember which way that it points. Make sure that you turn off your HVAC system to stop the airflow. Remove the old air conditioner furnace filter and discard it carefully so you don’t put the dust and other airborne contaminants back in the air. Write the date you install the air conditioner furnace filters on the place indicated on the side of the air filter frame.

If you have not experienced a decrease in mileage or engine performance, chances are your filter is fine and does not yet need cleaning. To be more specific, the filter does not require cleaning if you can still see the wire screen on the entire air filter regardless of how dirty it may appear. When the screen is no longer visible some place on the filter, it is time to clean it.

No. An engine can only draw in a certain volume of air depending on the engine’s size (measured by such things as bore, stroke and number of cylinders). Vehicles are designed to accommodate large changes in air pressure so they can operate at sea level or at an altitude of 14,000 feet. Engine computers adjust the amount of fuel required as a result of changes in air pressure (density).

K&N has an active Custom Air Filter Program to meet the needs of consumers with special filtration needs. We offer thousands of possible configurations of custom filters, in different shapes, dimensions and heights. Click here to read more.

Use a K&N Filter Care Service Kit, available at all major auto parts stores and a low pressure nozzle-free garden hose. A filter cleaned with K&N cleaning products will ensure a lifetime of performance from your air filter. Instructions for cleaning your K&N air filter are on our Air Filter Cleaning Instructions page.