Yes, indeed! This will not harm your humidifier. Promoting good air circulation and continuous filtration in your home has lots of benefits. Most modern furnaces have a low speed setting for continuous operation - refer to your furnace manual. Since the Desert Spring Humidifier is so efficient, you can actually add humidity even when your furnace is not on its heat cycle!

In most cases I recommend for the fan to be run on Automatic for better humidity control. When the air conditioner cycles off, the inside coil is saturated with water. If the fan continues to run the moisture will be blown back into the home. This decreases the dehumidifying capacity of the air conditioner. There are some homes that need the fan to run on continuous because of rooms that have a faster warm-up time than the rest of the house. See similar questions...

Modern air conditioning systems often use fan delay timers to keep the circulating fan running after the thermostat is satisfied. The reasoning is pretty simple: The evaporator coil is still cold, so it makes sense to get all the cooling you can for the money you're spending in energy. Furnaces have always run for a short time after the call for heating has ended. See similar questions...

Yes, running your furnace with the fan switch set to "ON" keeps the air constantly circulating to make your home more comfortable and filters the air. Combine this with an electrostatic filter to reduce the dust in your home. During the warm months, the circulation will also provide a cooling effect. And this fan position uses very little electricity. See similar questions...

For units that have been purchased after 2000, when you open the cap (not the battery end) there will be 4 switches on the opposite side of the circuit board from where the cap snaps in. The 1st switch from the right (or the 4th switch from the left) is the continuous read switch. To change to continuous read mode, pull the switch forward (towards you). See similar questions...

Yes. By building a summing Y-cable (check out Why Not Wye) and connecting it to the MAIN OUTPUTS a mono signal may be obtained. See similar questions...

Yes, you have to have some form of X server (unless you're running Windows, of course). It needs an X server for image processing, and for font manipulation. However, if you wish to run in batch mode, you can run with a special, frame-buffer-less X server called Xvfb, which doesn't require a graphics card or mess with your screen: Xvfb :1 -screen 0 10x10x8 -pixdepths 1 & gimp --display :1.0 --no-interface --batch "commands" .. See similar questions...

No, BitWise does not offer a pure direct to IP mode. The reasons for this are many, but the most important is that it would be difficult to incorporate it into the program without making the program needlessly more complex. Further, without being able to use the server for authentication, there would be no way to validate users as they "log in" and therefore the username system (and the reasonable assurance of who is on the other end) would be useless and unreliable. See similar questions...

Answer: You need the correct printer driver in Interact to match your printer. A Printer Drivers Utility program is available. This utility is available to Product Support Program (PSP) members. Please contact your local distributor for more information about the PSP program. Answer: On a Remote Message Display tool, use the Link variable: LINK\ALARMS:A in the Message Text Output field. Question: I am getting the following error message: "Cannot initialize PTM. See similar questions...

The slower the fan speed is, the hotter the air will be. In general, we recommend a medium to medium high speed. See similar questions...

SLI mode is only capable of running one monitor per card at a time. To run in quad-head mode, you must disable SLI mode. However, while older drivers required a reboot to switch modes, the NextDimension uses the latest drivers and does not require a reboot to switch modes. See similar questions...

The "safe_mode" disables several important PHP commands, including input/output functions and file upload support. This makes it virtually impossible to run a complex ecommerce software like X-Cart. Our shopping cart software needs input/output functions in order to read the template files, needs file upload functions in order to handle product image uploads. By default, "safe_mode" is turned off on all PHP installations. See similar questions...

Ultra ATA/66-capable device. (Seagate drives require an activation utility for each device.) Ultra ATA/66 technology is defined such that the PC and the hard drive can both detect the presence of the required 80-conductor cable. The system board must have a special capacitor on pin 34 to detect the cable. The cable must have a notch cut in line 34 to correctly detect an Ultra ATA/66 device. Go to Top See similar questions...

Earlier AC 23 units did not offer 2-way mode operation. They run 3-way stereo, 4-way mono and 5-way mono only. Externally combining a pair of signals -- mids and highs or mids and lows -- provides a means to achieve 2-way functionality. As above, the summing Y-cable is used to mix two signals together, (see Why Not Wye?). The AC 23 has switching jacks and must have connectors plugged into every jack (as shown in the AC 23 manual) for the configuration being used. See similar questions...

Yes you can, if both frequency selectors are set at the same crossover point. The high frequency output will be 6 dB lower in level than the low frequency output. It is much better to use the SAC 22 or AC 22B for a 2-way application. See similar questions...

It appears that the OS X Classic engine does not allow QuickTime video input in most cases. We have had reports of some users getting this to work but in most cases it appears that the QuickTime FireWire input does not work in Classic. If you have not yet purchased the software, you can use the demo version to determine if video input will work for you. See similar questions...

Worms Forts is set to full screen rendering mode to ensure the game runs optimally on minimum specification systems. It is however possible to run in windowed mode if you so wish. In order to change the game from full screen to windowed mode the shortcut must be manually modified. Note that this option may be combined with manual resolution settings in point 5.7 also. See similar questions...

You may not have write access on the network. You must have administrative access when installing to the system directory. See similar questions...

The free-run mode is the operating condition of a clock whose output is totally internally controlled. The clock has never had, or has lost, all external reference input, and has lost all data from a previously connected source. The specifications for free-run accuracy apply over the lifetime of a clock, typically for 20 years. See similar questions...