When DCI engineered the SmartVent product, standard techniques for roofing were not changed or modified. Therefore, install the drip edge against the wood facia and wood roof deck, then cut the slit measuring from the corner of the drip edge, then install SmartVent. Some roofing technicians prefer a second drip edge on top of the SmartVent which is not required. (If the second drip edge is used, ensure a 3/4” space remains between the flashings and the SmartVent.

The flexibility and range of choices for a drip system can be both a blessing and a curse. One easy way to get started is with our Heart of the Garden Starter Kit and one or more add-on packages. We also have some special purpose kits to meet other needs such as misting or container gardening. Be sure to check out the other resources on our web site such as the system map and the design considerations pages to help get you thinking about drip. See similar questions...

It is an L-shaped strip of metal installed along the roof edge to allow water to run off to rip clear of the roof deck and eaves. See similar questions...

Drip edges are used for watershedding at the eaves and rakes and for preventing wood materials from rotting. It is important that the drip edge is "made of a corrosive-resistant material that extend approximately three inches back from the roof edges and bends downward over them." (Residential Asphalt Roofing Manual, 1997) The drip edge should be applied beneath the underlayment or eave protection along the eaves and over the underlayment on the rakes. See similar questions...

Different areas require different treatments. Larger areas, lawns, would usually be watered with rotary heads because water is distributed over a larger area. For smaller areas we use smaller mist heads. We use drip systems for small tight shrub beds, gardens and areas prone to prevailing winds that would blow the water in the wrong direction. back to top See similar questions...

The hooks molded onto the C7 & C9 LED light strings currently on our site will not fit over a gutter, and I don't think it's deep (long) enough to sufficiently grab a drip edge. They are made more for narrow tree branches or supporting wire. Consider using our Shingle Tab light clips or Gutter clips. Find them on our Accessories page soon. Or email us if you can't wait for the website update. See similar questions...

No way. Only certified and trained installers and Putter's Edge Dealers can install the Putter's Edge Turf System. That's why we're here! See similar questions...

The drip system gives you continuous delivery of nutrients to the plants. You don’t have to worry about floods as much with a drip system. See similar questions...

In some instances it's possible to design a small system without knowing your flow. However, we don't recommend this! If you don't know your flow you can easily design a system that puts out more water than you have available. The end result is a system that doesn't work and that gives you more stress than doing your taxes on April 14th. Sometimes you can have a small system that works for years suddenly stop working if you add on in a way that exceeds your flow. See similar questions...

Lawn sprinklers and drip emitters operate in a different way. Sprinklers put out a lot of water and are run for a relatively short time, while drip systems put out a little water and are run for a longer period of time. For this reason, you would not want to put lawn sprinklers and drippers on the same zone. In this situation, you would have one zone for the drip system and another zone or zones for the sprinklers. See similar questions...

According to chemical studies, the optimal water temperature for drip coffee is 95-98C. According to my notes, colder water doesn't extract enough caffeine/essential oils from the beans, and above such temperature the acidity increases wildly. Fact: Unless you are buying some major debris, bean quality is not very important, as compared to 1-3 and 5. Fact: A coffee can in the supermarket often contains major debris, so be careful when you choose. (See note below). See similar questions...

EDGE (Enhanced Data rates for Global Evolution) is a technology that enhances the ability of delivering voice and data services, approximately triple the rate of data transferred over the current GPRS network. It will enable faster access to WAP and web browsing, MMS, video and audio streaming, mobile office application and interactive gaming. See similar questions...

Edge detail refers to the edge size and shape of your finished project. In terms of size, most slabs are cut to a 3/4" thickness. The exposed edge of your finished project can remain at 3/4" or be "laminated" which results in an 11/2" finished edge. Laminated edges are often chosen to provide an attractive overhang between counter tops and cabinetry. The second component of edge detail is the shape. There are many different shapes to choose from. See similar questions...

cd ~ mkdir klamavcvs cd klamavcvs cvs -z3 -d:pserver:anonymous@klamav.cvs.sourceforge.net:/cvsroot/klamav co -P klamav cd klamav make -f Makefile.cvs ./configure make su -c 'make install' Getting the install script to work in SuSE 10.0 was a real pain. I thought it might be helpful to pass along what I did to make the script work: 1. Install these packages with YaST: kdelibs3-devel kdebase3-devel kdebindings3 qt3-devel-tools qt3-extensions qt3-static libjpeg-devel curl-devel km-dazuko 2. See similar questions...

Focus not on the brew method but on the amount of ground coffee used to make what you drink. Caffeine is easily percolated out of the ground coffee into the cup, so the amount of caffeine tends to be a direct result of how much coffee is used to prepare the beverage. Some people use little coffee, make weak dribbly espresso and get little caffeine. So a certain brew method isn't necessarily stronger than another. Many more information sheets.. See similar questions...