For the best speaker damping and least amount of power loss you will want to use the heaviest gauge that is practical. The length of the speaker wire should be considered when considering wire gauge. The shorter the run, the smaller gauge you can use with minimum power and damping factor loss. The longer the run, the heavier gauge you will need to minimize power and damping factor loss. You will also want to consider the size of power amplifier you are using.

the gauge of wire depends on the power of your amps as well as the length that you will be running the wire. to find an exact answer, go HERE See similar questions...

You will need a standard usb cable (the one that is included in the box when you buy the phone). Because you are going to use a usb cable you have to install drivers for this cable. You can find this drivers at the downloads page If you do not have this cable you can buy it from us. For now go to contact site to ask us for the cable. You can also buy it in every electronic store and ebay. It's often the same cable as used to connect digital (video) camera's to a pc. See similar questions...

The wire gauge varies by type of crate. The main ones used are 6-, 9- and 12- gauge wire. See the specifications on each type for actual gauge. The "Fold & Carry" crates fold into a suitcase-like package with a handle in the center. The "Pin Series", a.k.a. "Square-back", take apart with pin construction into a flat package due to the interlocking panel construction. These crates are put together by use of a "Shepard's hook" pin. See similar questions...

While there is no such thing as "too much" power in a sound system, the system should be powerful enough to fill your room. To help you pick the right product, each HSU speaker and subwoofer has a "Loudness Level" index —a rule-of-thumb guide to point you towards the best system for your space. See similar questions...

Yes. Any speaker wire will work, but we don’t recommend using wire thinner than 16 gauge. For the best audio performance we’ve included 12 feet of 16 gauge wire with each system. See similar questions...

Speaker Wire Technology (SWT) is an exclusive Matrix technology which allows both data and audio signals to travel over the same four conductors of wire. The versatility of SWT allows Matrix Audio products to be connected in a multitude of wiring configurations including instances where the control wire has been run separately from the audio cable. See similar questions...

Answer: You must use a two pair shielded cable. Biamp recommends Gepco UNC220 or equivalent. Use the data pair for Hi and Low, power pair for + and -. You can also use Cat5 cable for wiring RCB devices. When doing so, observe the following wiring scheme: See similar questions...

Soldering heavy gauge wire is one of those things that is an acquired skill. Like many things, once you learn it, it becomes relatively easy. Silver solder will produce a MUCH stronger joint. It comes with a liquid flux. It is more sensitive to the correct temperature and it is also more expensive. Start by making sure the wires are very clean. We recommend sanding them where they are to be soldered with 150 grit sandpaper. Then clean them with alcohol (isopropyl, rubbing alcohol). See similar questions...

The longest working installation we know of is 650 feet. The cable normally supplied with a system is 40 feet. Longer lengths can be supplied on special order. Customs lengths can be provided with about 2 weeks lead time. We also offer optional 40 foot extension cables. See similar questions...

Wire and cable is our forte, however, we also sell tubing, connectors, cable assemblies, and cable ties, to name just a few. Our products serve numerous markets including, automotive, electronics, military, and shipping industries. Home | About Us | Products | Testimonials | Custom Cable Design Center | FAQ | Partner Links | Contact Us | Site Map See similar questions...

ANSWER: This depends on the size of load you will be placing on the channel. A full 10A load typically requires 16AWG wire. Please refer to the National Electric code or other manufacturers' guidelines for proper wire sizing. See similar questions...

I like to use dead soft wire for most of my pieces as I mainly manipulate the wire with my hands and fingers. I use a variety of gauges from 18 to 22. See similar questions...

If the adapter cable is used for charging and cycling batteries from 2 to 12 cells the length and gauge of cable is not critical. Only 18 gauge or heavier and 36 inches or shorter cable should be used with "V" device. This is necessary because the second four digit reading of the "V" device is taken under heavy 1000mA load and thin long cables will have a large voltage drop. This will result in voltage at the battery being higher than at the Alpha4 port jack. This will cause flashing V. See similar questions...

The input and output terminals on the selector will accept speaker wire sizes up to 12 gauge. The minimum recommended size for speaker wire is 16 gauge. In-wall wiring should be CL-3 rated. See similar questions...

Each containment system will come with 500 feet of wire. Each additional boundary wire kit will come with 500 fet of wire. Here is a table to help you make the correct decision. See similar questions...

Not technically, but some cable operators require that you do subscribe to basic analog cable TV service before you sign up for high speed Internet access. Check with your local cable company for specific information. See similar questions...

Maybe. There are a number of different competing gauge standards (14 gauge brass is not the same thickness as 14 gauge copper or 14 gauge stainless). On individual product listings, we do have the gauge listed (where that information is available). As a long-term proposition, though, you should design and order in decimals (i.e. .032") as there is less chance for errors. See similar questions...