Fuel injection is a replacement for the carburetors that were around since the dawn of the automobile. There are many basic types of fuel injection, but we should start by saying what a fuel injector is - it's basically an atomizer, something that sprays a mist of gasoline into the air. This helps the gas to mix better with the air and stay in an even suspension, so that it burns more evenly and creates less pollution and more power. (Think of cooking spray vs.

Immediately after the injection, you may feel your upper extremity getting warm. In addition, you may notice that your pain may be gone or quite less. You may also notice "a lump in the throat" as well as hoarse voice, droopy and red eye, and some nasal congestion on the side of the injection. You may also develop a headache.

NBB maintains the largest library of Bioheat® fuel and Biodiesel information in the world. Most questions can be answered through a review of the information on the National Biodiesel Board website located www.biodiesel.org. If further information is desired, you can email your question to the NBB at info@biodiesel.org.

Fuel injected engines are self adjusting, automatically idle themselves back when the lubricant is improved with Tufoil, just as the carburetor would have done.

We still enjoy working with the Carbureted setups, they also have a more traditional look to them as well. Easy to tune and less complex. We do provide a Fuel injected setups with the complete Throttle Body, injectors, fuel Rail, wiring harness, computer and sensors to plug in. The EFI Mass Flo setup is an easier way of going. Figure Approx. another $2,000-$2,500 over and above a Carbureted setup. It's recommended that you have technical knowledge on Fuel Injection when dialing in the engine.

Fuel injection is not necessarily any more complicated than a carburetor. It may seem more complicated to a novice fuel injection enthusiast, but in reality, carburetors can be more complex. A typical Holley carburetor has over 120 possible adjustments. A stock TPI intake has only three items which can be adjusted, both of which are on the throttle body (throttle position sensor, idle air control valve, and minimum air screw).

Besides throttle bodies, linkage and manifold (if required) typical components are; A management system , wiring loom, fuel pump, fuel pressure regulator, fuel injectors, appropriate plumbing, air horns and a ducting/filtration system for the incoming air.

There are many benefits. The quantity of dirt in your vehicles fuel injectors and carbon deposits in your engine's pistons and valves impacts how noticeable these benefits are. Benefits include:

The major differences between large commercial boilers and electrical generation units and home heating oil applications are the gallons per hour being combusted. Large or small-scale boilers or electrical generation systems all have the same fundamental considerations as home heating applications. All the same advantages, and precautions, apply to these applications as they do in home heating applications.

You're right in believing that fuel injection is complicated. Factory engineers and technicians spent thousands of hours "mapping" your car's engine computer (ECU). Your ECU includes numerous fuel maps to deal with a wide variety of load and environmental situations. The signals sent to your fuel injectors are the result of all this knowledge. Rather than pretend we can create a better map, we let your ECU calculate the load, and temperature, and price of coffee at Starbucks.

ldquo;Yes”, we recommend that you see a qualified technician for fuel re-mapping or have an aftermarket fuel module installed.

If your vehicle is equipped with factory fuel injection stay with it. We offer several upgrades to make it perform better. We currently do not recommend after market fuel injection systems. They are over complicated, over rated, over priced and prone to failure. NASCAR and NHRA still run carbs. Our experience and a number of independent racers will tell you that their is no real gain in power. The injection system is usually better on emissions and thats why big government secretly pushes it.

There is no comparison. The WhiTek ECS will run any Harley engine, Sportster to EVO, stock to stroker, normally aspirated or supercharged. It will work with any cam, displacement, or compression ratio. It includes a control/display unit that is used to adjust it while riding. It is easy to install, and results in a neat, clean installation, since all of the components are contained in one unit.

Edelbrock and Accel have multi-port fuel injection (MPFI) systems, however the Accel must be tuned with a laptop PC. These are quite expensive though. Force Fuel Engineering in Florida can handle a conversion if you send them your manifold. They recommend an open plenum manifold, but they can do 180 degree manifolds, too.

Alcohol is very corrosive and, unless you are prepared to constantly maintain your fuel system, we do not recommend it. Larger injectors and fuel pump are required due to the additional flow required.

Side effects vary from patient to patient. The most common side effects, however, are slight numbness in the legs and headaches. If these symptoms don’t subside within 2 days after the injection, contact the doctor.