Answer: Acquinox? dual flush toilets will save you over 6,000 gallons of water per year for a family of 4. The Dual Flush system gives you the best of both worlds: The Low Flush uses less than 8/10s of a gallon of water while the Normal Single Flush uses 1.58 gallons ? still within conservation limits.

In a dual-hose Venturi Series dry ice blasting system, an ejector type nozzle, similar to a conventional abrasive media blasting nozzle, is used to combine the compressed air stream with the dry ice particle carrying vacuum stream created by the ejector. In Cold Jet's single-hose Radial Feed Series dry ice blasting systems, the dry ice pellets are mechanically fed into the air stream. No energy is wasted creating a vacuum to pull the pellets through a separate line.

Yes, we distribute 400 porta-potties around the city for general public use and another 50 in special locations throughout the city (like the Airport, medical facility, etc), in addition to some in Empire and Gerlach. The potties are serviced on a continuous and rotating basis, 24 hours a day during the event. We do our very best to keep them clean and stocked with toilet paper.

A single source selector (ISM models) accepts input from one audio source (receiver/amplifier) and distributes audio output to a number of zones or speakers. However, a dual source selector (DSSM, VSS models) accepts inputs from two separate amplifiers/receivers and allows the user to select the program from one of the two sources for each zone output. With dual source selectors, the audio programs from both amplifiers cannot be selected at the same time for any zone output.

Depending on each application, either single-rate or dual-rate springs are available. Dual-rate springs are just that-- a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs collapse they result in a soft, or initial, rate. The spring set will retain this initial rate until the short spring stops compressing. At that point, the spring rate "crosses over" to the stiffer, or final, rate.

It is easy to confuse a dual voice coil sub as a better subwoofer, but that’s not the case. You will get the same output from either sub when used in the right application. Both sets of terminals must be wired up when using a dual voice coil subwoofer. Your amp and the number of subs will determine which subwoofer you would want. For example, if you had a TA5601 amplifier and wanted to run a pair of 12s, you would want single voice coil 4Ω woofers.

Single power source modules needs just one 3 - 5V power supply for the entire module. The module contains an inverter that supplies the operating voltage for driving the liquid crystal. Dual power source modules need a 3- 5V power supply for the LCM and another power supply to provide the Vop for the liquid crystal.

The difference between dual track and single track is that single track holders hold one line of tags while dual track holds two lines of tags. Click here to view E-Z tags and holders.

The single-action clamp is a one piece assembly - both the clamp and the base are attached to the turntable. Unfortunately, the brake of the single-action clamp wears out with frequent use, requiring regular maintenance. In 1990, the Wilson Sporting Goods Co. introduced its Pro Staff (Prestige) stringing machine, which was manufactured in Taiwan. It utilized the single-action swivel clamp assembly, and it had brake problems (as mentioned above). Wilson Sporting Good Co.

If radiators on a single pipe system have severe deposit build-ups, or cold panels, then the Power flush is not likely to be successful. BS7593:2006 advises against power flushing a single pipe system. If you do take on such a system, improve the chances of success by pre-treating with two litres of HYPER-FLUSH, and operate the flow reverser more often than usual whilst flushing individual radiators.

Dual-Flush toilet technology allows the user to select a short flush (1.1 gallons) for liquids or a long flush (1.6 gallons) for solids thus taking water conservation one step further. Take a look at our All-in-One 1000 Series toilets featuring Dual Flush.

Please contact the Front Desk at their residence hall. Front Desk telephone numbers are listed on our Contact page. [TOP]

Many people prefer to subscribe to this list in "digest" form. This means that all of a day's messages are combined in a single email message with a table of contents. Due to network traffic and other factors, digests aren't received at the same time each day or even at the same time by all subscribers. It's not unusual for digest posts to be separated by more than or less than 24 hours. Occasionally, two digests may arrive on the same day.

The Class Five is designed for extraordinary bulk flushing performance. Its large flush valve allows rapid release of water combined with a direct fed jet and maximizes water flow. The Ingenium has a quieter, swirling flush designed to minimize noise and clean the bowl.

The single-side foil is great for acoustic applications where sound can be absorbed into the natural fibers. The dual-sided foil provides an excellent radiant heat barrier to resist heat flow.

On Thiaoouba they use a kind of device that looks similar to our toilet, but isn't. It simply disintegrates the waste as it comes out - into elementary particles I guess. No water, no paper, no smell, nothing. Michel was scared that this machine might disintegrate his private parts... People get stuck in the parallel universe for thousands of years. Killing them there is a sort of favor, because their astral bodies are liberated and can progress on the path of reincarnation.

Would be fun but, no toilets aren't in the dark! The toilets are located on ground floor level and first floor lounge and are fully lit.

the ohm load is the total resistance that your amp is seeing when wired up to the subs/speakers. In general, lower ohm loads will mean that your amp will be putting out more power. However, you need to make sure that your amp is stable at that ohm load or you will cause significant damage. The ohm load can be changed by wiring the subs differently, ie. Parallel vs. series. To determine ohm load when wired in series, the ohm load = Resistance1 +Resistance2+Resistance3+....