Ping command is only used on local network. With a PC or a notebook computer, you can assign an IP address to WebEye connected on local network with ping command or setup program. If you cannot assign IP address to WebEye with ping command, you should check under written 2 points. First, you watch the LED in the rear of WebEye. For accurate judgment, you disconnect and re-supply power to WebEye. WebEye has two LED of yellow and green in the rear.

If you want all the edits of one IP to be attributed to an user, see How do I reassign edits from one user to another? above.

If you have obtained a static IP from your Internet Service Provider (ISP) and wish to configure your adapter with your static IP settings, please follow the instructions below: Subnet Mask If you are using a router, please contact your router manufacturer for instructions for retrieving this information from the router directly (this will typically be from the router's own administration pages). If you are not using a router, please obtain the above information from your ISP.

add the ip to the guest's network context (a guests NID is the same as the XID {context ID}) naddress --add --nid <nid> --ip 194.169.123.23/24 update the config in /etc/vserver/<servername>/interfaces to reflect the changes for the next guest restart (if desired)

For example, if your PC connected to a router with IP address 192.168.1.1, after you type C:>ping 192.168.1.1 you get reply from that IP address, that means your PC is connected to the router. For example, if you type C:>ping 66.218.70.50 you get reply from 66.218.70.50, that means your PC is routed through router to the 66.218.70.50 web server. If you type C:>ping www.yahoo.com then you get reply from 66.218.70.50, that means your PC set up with working DNS server.

Using the 'Ping' commands in UserGate is not possible at the moment, because UserGate does not allow ICMP traffic.

Blacklisting an IP address blocks incoming traffic from that IP address. And if you set BLACKLISTNEWONLY=Yes in shorewall.conf, then only new connections from that address are disallowed; traffic from that address that is part of an established connection (such as ping replies) is allowed.

Yes, you can ping CalPOP.com 216.240.152.9 or you can go to http://speedtest.calpop.com you can even go out onto the net and do some testing from around the world http://www.traceroute.org

Yes, but this is the very nature of direct connections. BitWise bypasses the server, so your PC must know where to send the messages (i.e. what computer on the Internet). Without sharing your IP address, nobody could connect to you, and BitWise wouldn't be very useful at all. You can't have it both ways: you can't have direct connects and not reveal your IP address. Does revealing your IP address constitute an insecurity? We do not believe so.

Most computers connected to the Internet are identified by a unique number called an IP address (for instance, 81.31.115.90). IP addresses do not correspond to a geographical location nor are they easy to remember. Also, IP addresses are FIXED (if you change web hosting companies you'll need to get a new IP address for your site).

In general, a static or dedicated IP address will only be available in conjunction with SSL. Please contact us at sales@cheaperwebhost.com with your needs.

First, remember that a "ping" is an Internet Control Message Protocol (ICMP) packet. It's a pretty simple as protocols go. ICMP is defined in RFC 792 and provides a way for IP stacks to send simple messages containing information or errors. Given this, it often gets the lowest priority of any protocol on the routing totem-pole, and may actually be rejected by routers if there is a lot of traffic on the network at a given time.

Start Button >> Settings >> Control Panel >> Network >> Add >> Protocol >> Add >> Start Button >> Settings >> Control Panel >> Network >> Protocol >> Add >> TCP/IP Each machine on the network needs to be given a unique IP address. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. You can set this by editing the TCP/IP properties on each node.

They should be conveniently located. Since sitting and driving often aggravate orthopedic problems, there should be a very good reason for you to drive a long distance for rehabilitation.

Unfortunately because of recent spam activity we have been forced to (at least temporarily) block all IP addresses. If you would like to join our board we'd love to have you. Registered members are able to bypass this block because the block only stops annonymous posting. So, please contact TJ to get registered and we look forward to your participation on the board!

Maybe. There are some advantages to having a unique IP for your site. When you change servers, you can point your users to a new IP, so they don't have to wait for the domain name change to propagate. With a static IP, it can also be simpler to upload and test your site before transferring the domain name to a new server. Setting up SSL is also much simpler. You may also not want to share your IP with some sites that could lead to your site being banned by search engines or spam lists.

Since it is quite possible for a user to mistype their password repeatedly it may be desirable to have DenyHosts prevent specific IP addresses from being added to /etc/hosts.deny. To address this issue, create a file named allowed-hosts in the WORK_DIR. Simply add an IP address, one per line. Any IP address that appears in this file will not be blocked. Additionally, as of v1.0.3, a valid hostname can also be placed in the allowed-hosts file.

Yes, we do offer IP addresses, although we do follow & ARIN guidelines. Most of the time you will be granted an IP address if you are going to use SSL or you are a reseller and require your own Private Name Servers. If you are able to justify your use of an IP address then you will be billed an extra US$3/month.