No, you do not need to use tile spacers to install the tiles. The chamfered edge provides an elegant look when installed "tile to tile". The 45-degree chamfered edge provides a natural caulking channel when the tiles are butted together. The XT-200 mastic allows sufficient time to adjust the spacing "by eye" for difficult areas. *Tile spacers can be used if you require large grout lines.

Only when installing over a porous floor, this means a floor that can "absorb" some of the liquid such as a plywood, or concrete sub-floor. DO NOT use another primer in conjunction with the Basement Proofer and never use primer when installing over existing vinyl flooring.

Met-Tile is made of 3-ft-wide steel panels, in lengths of two to 20 feet. Since the panels are stepped to create a tile-like appearance, they are commonly referred to as "tile panels" or "tile facsimile panels."

Yes you can. All you need to do is provide a Radiantec mixing valve to step down the temperature of the water to the radiant circuits. You mix hot water from the boiler with return water from the floor to provide a lower temperature.

This is largely a design choice. If your heaters are standard height, we recommend that you order your wainscot with a base height 1-3" above the heaters. If they are tall, like older ones that are sometimes 24" tall, we recommend that you just ignore them for ordering purposes. During installation, you will just cut around them.

Modify the 'autoexec.nos' file for your needs, or convert one from TNOS/Dos or another variant of xNOS Before connecting TNOS/Linux to a TNC: You should look in the /etc/rc.d directory and see if you have an rc.serial file. If you do, examine it, as it MAY need to have some changes made to it before the serial ports will be ready for use.

There are tools designed especially for this purpose. The Super Guide by Hyde? Tools is a metal shield that can be placed between the carpet and the baseboard allowing you to paint one section at a time. Another method is taping the carpet with masking tape or masking paper.

No, the system generates low temperature heated product that works well with radiant floor heating systems, warm air heating, Solar Domestic Hot Water (SDHW) heating systems and other types of low temperature heat distribution systems.

You have several options: call your regional Hanson Sales Representative (see the Contact Us link on this website), or use our link to request a sales representative contact you. A list of Hanson Roof Tiles Distributors is also available on this site, through either the Locations, or Contact Us links on this site. BACK TO TOP

Met-Tile weighs only 125 lb per square or 1.25 lb per square foot. Concrete and clay tiles can weigh up to 10 times as much. This means you can reroof with Met-Tile with no need for costly truss reinforcement. And it's safer than heavy tiles in earthquakes or hurricanes.

Before installing this component, you should make sure that the Joomla root is writable (aka the directory where index.php lies), and the administrator directory is writable. Also make sure that /index.php, /administrator/index2.php, and /administrator/index3.php are writable. Then go ahead and install the component! It will automatically attempt to make all necessary file modifications necessary for the component.

A baseboard heater requires 30 to 60 minutes to heat the room, provided the heater has been properly sized (adequate wattage) for the room. Baseboard heaters are longer, but not as tall as a fan heater. For example, a 1500 watt baseboard will require 6 feet along an outside wall and is about 7 inches tall. A Register Plus heater grill is 14 inches wide and 7 inches high. Baseboard heaters operate at lower temperatures, making the surface temperatures of baseboards cooler.

The dirt streaks that are being created above your baseboard are mainly dust, dirt, and carbon soot that might come from fireplaces, water heaters, furnaces, standing pilot lights, candles, cigarette smoke, cooking byproducts, and even automobile exhaust by the natural convection that occurs during the heating cycle.

No, the bottom of the fan hub has a raised area to rest on the inner race of the front engine bearing and does not require the washer. Plus the wash causes the clutch to be that much higher. Ideally the bottom edge of the clutch should be at the bottom edge of the clutch liner.

FREE DIRECTV installation is done by top-of-the-line professionals, so you don't have to worry about setting up your system; you know it will be done right the first time.

See SGML for Windows NT: Setting up a free SGML editing and publishing system on Windows NT/Cygwin by Markus Hoenicka.

Do we look stupid? Needless to say, the fiber optic cable that enables TiSP will not interfere with your toilet's regular operations. For your own convenience, however, you may eventually wish to hire a professional contractor to help route the cable under, or through, the toilet seat to your TiSP wireless router.

Floor tile adhesives (mastic) can be removed with chemical paint strippers or citric acid solvents (delemonene), which do not emit VOC fumes but are effective only on modern water-based adhesives. Mastic removers are sold in stores. We use our Lightning Strip paint & mastic remover, particularly for the old, thick, black mastic. Test it on a small area first. Avoid filling the pores in concrete with diluted mastic. Afterwards, wash the area to remove any residue.

With ThermaPureHeat® there is rarely any need to walk on the rooftop, effectively eliminating roof/tile damage caused when fumigating.