This is the height of the space that an overhead door will need to cover. If you provide us with the TODCO serial number, we have the opening height of your door on file. If the serial number is not available, please provide us with two actual measurements: 1) the height of your trailer, from the inside floor to the inside ceiling, and 2) the distance from the inside floor sill to the underside of the header.

This is the width of the space that an overhead door will need to cover. If you provide us with the TODCO serial number, we have the opening width of your door on file. If the serial number is not available, please provide the actual measurements of the width of your trailer, from the left inside wall to the right inside wall (post to post), along with the name of the manufacturer of your truck body or trailer, and the year it was made.

The Garage Door Screen is mounted (in front of the doorstop, one-inch wood strips) on the header and the doorjambs which the garage door is mounted to.

To get the standard height measurement of the opening, be sure to measure the height in several locations. Normal gates are 3/4" off the floor when installed and are built normally to the shortest dimension. Watch for irregularities in the flooring and be sure there is room above the opening for face mounted gates. Always measure the "finished" floor to the top of the track.

Yes, the screen frame is offset to compensate for this. The adjusting screws for the screen wheels need to be facing the interior of the house. If the screen is installed‘backwards’ then the handle hits the patio door.

The panel height and opening width are mainly restricted by the maximum permissible panel weights. These in turn depend on the operator being used. In addition, however, it will be necessary to remain within certain height/width ratios that have been specified in order to ensure the smooth and low-wear running behaviour of the door system. You will find guide values in the relevant technical brochures. For additional information, please consult our sales advisors who will be glad to assist.

Width is measured from edge to edge. If it is a slit seal bag measure inside seal to inside seal or inside seal to fold. Remember, every application is unique; the following information is intended to provide general information and guidelines. Please call our Technical Service Team at 763-225-6600 to discuss your specific need. In most cases, desiccants and oil are not necessary when the part is protected with Zerust® / Excor®.

Our Roll-Up Doors are attached to the wood guide rails which are part of the door package, and require support of vertical walls.

To achieve a single access door you would require an odd number of panels to stack in one direction i.e. 3, 5 or 7, etc or to split the stacking to both sides in order to achieve an odd number configuration to at least on side, i.e. 2:1, 5:1, 5:3 etc. To achieve a French door opening, you would require an odd number configuration to both sides, i.e. 1:3, 3:3, 7:3, etc.

Garador stock all current Garador Controll-A-Door Remotes as well as a range of remotes from obsolete autos; please refer to automatic accessory page.

No other manufacturer offers more styles, colors and windows than Clopay Classic, Murray Shaw's supplier of choice. Choose from Clopay's Pro-Series and never paint your garage door again.

Both the HP and HS (at the tall height) are designed to fit in a standard 8 foot ceiling (about 7 1/2 feet). The HS has a short ceiling setting at about 6 1/2 feet.

For single doors, as a general rule, add 2" in width and 2-1/2" in height to the nominal door size for single doors. For instance, a standard 3/0 x 6/8 door would require a 38" x 82-1/2" rough opening. Pairs would require twice the nominal door width plus 2" as well as an additional 1/2" if there is an astragal ( between them. For example, a standard pair of 3/0 x 6/8 doors with an astragal would require a 74-1/2" x 82-1/2" rough opening.

For all prehung units we REQUIRE that you provide us with your rough opening size. We will build the unit to fit the rough opening size that is provided. If this is for new construction, we normally add 2" to the height of the door and a total of 2" to the width of the door for a rough opening. This allows for the thickness of the jamb and leaves an extra 1/2? in width and height to square the unit.

Klaus Parking Lifts are designed for allowing easy access to the cars parked on the platforms, passengers and luggage should be loaded or unloaded when the car is off the machine. The car should be parked as far to the right side of the platform as possible to allow the most space for the driver to access the car. The lift platforms are available in several widths and it is best to use the widest possible.

szlig;-Quantification (ultracentrifugation), non-denaturing gradient gel electrophoresis and nuclear magnetic resonance (NMR) are being used to determine LDL particle subfractions.

A fellow trailer owner, Brian Jenkins, needed one when restoring his trailer, and borrowed one from a friend and had a duplicate mold made and extra castings. They are available from Vintage Trailer Supply. We need more people helping out like that....

Book sizes are based on the practice of folding a large sheet of paper to create several pages. A traditional sized sheet (e.g., 25 x 38) which is folded twice to create four pages yealds a quarto (4to) sized book (measuring 12.5 x 19), a sheet folded three times to create eight pages yields an octavo (8vo) sized book (measuring 9.5 x 12.5), and so on. If you're mathematical, you'll notice that the number of pages is two raised to the number of folds (2**3 = 8).

LDL subfractions provide a more in-depth assessment of CAD risk while the commonly performed total LDL cholesterol test gives limited information.

BALANCE is finding out whether people taking combination treatment are more or less likely to take additional drugs or be admitted to hospital for new mood symptoms than people taking lithium alone or valproate alone. (Click here for a list of other measures of effectiveness and safety being assessed in BALANCE.)