Use Sticker-Off! Decal Adhesive Remover. Just spray it on the adhesive, allow a few minutes for the product to penetrate and then wipe away with a clean, soft cloth.

Removing old decals is a job all to its own. There is no easy simple way to remove decals. It always takes time and effort. After decal material is removed, adhesive residue usually remains. Any decals that do not have clear coat paint will be easier to remove. Use a heat gun to loosen the decal and begin to lift the decals. Not too much heat to burn the paint, and use extreme caution with plastic parts. Heat guns are hot enough to melt plastic.

Use a hair dryer to warm the decals and they should peel right off. Do small sections at a time. If you use a heat gun, be careful not to burn your paint or finish.

More often than not, YES! Let the stained item soak in a solution of Stain Solver liquid overnight. If the stain is still there, increase the concentration and try it again. Continue to increase the concentration until you succeed or fail. Remember, you have NOTHING to loose. Until such time as the stain is removed from the garment, it is headed for the rag pile.

The best thing to do is probably bag it up and take it to a landfill. At least it’s organic and will rot away. Make sure you don’t put the infested mulch somewhere where you could be held responsible for someone else’s artillery fungus problem. This is out of my field, but it has been suggested that the infested mulch could be put in a yard waste-composting facility. But you really need to ask this question to a “compost expert.

The enucleation procedure is usually performed under local anesthesia, which involves numbing the entire eye and socket tissues prior to surgery. The operation is relatively simple to perform. Immediately after the eyeball is removed, an orbital implant, only slightly smaller than the natural eye, is inserted deep in the socket. In some instances a plastic shell called a conformer is placed over the implant to preserve the shape of the eye.

Removal of existing appliances can be done at a charge of ?10 per appliance, however this must be agreed with electricshop at the time of ordering and appliances must be disconnected ready for transporting beforehand. Please note: this service can be offered only when deliveries are made by electricshop staff and not third party couriers or some manufacturers.

Yes! The new cover will not stick or fit properly if applied over an old covering, even if the original is in good condition. In fact, you'll spend more time removing the old cover and cleaning up the camera than you will putting on the new cover. The ease of stripping the old cover varies, but in general the older the cover, the more effort needed to remove it. Most cameras made since the mid-70's can be stripped off quickly; almost as if you were removing tape.

In order to get a perfect fit, we recommend that the old tops be removed prior to templating. Not removing the old tops can result in gaps between the stone and the wall and backsplashes that don't fit properly. Also, since Formica-type tops hide cabinets that are not level, your installation could be delayed significantly if this is discovered on the day of installation.

Yes we can, the cost is ?20.00 per hour to remove the hardboard. We put the rubbish at the front of the house.

No, unfortunately we cannot remove old beds, because Silentnight do not have the infrastructure to deal with the disposal of old items. However, most good councils offer a furniture removal service that will arrange disposal of such items.

This is a service limited to certain manufacturers. Please contact us on 0800 028 0513 for details. Back to top

It’s not always necessary to remove the old veneer but it should be intact, not bubbled or cracked, and firmly attached, if you are even considering veneering over it. If you are forced to remove old veneer, a heat gun and a putty knife are essential tools. You must first apply heat to the edge of the veneer to loosen the glue. Then start with the putty knife under the edge and lift as you go. This process can be slow and the veneer will likely come off in small chunks.

It's a matter of temperament, if you want the leaves on the stem or not, some species look "wrong" with old leaves others look "wrong" with out leaves.

All commercial & custom transfers require them to be heat pressed with a heat press machine with 40 pounds of pressure at 375-390 degrees for 8-20 seconds.

If you do not intend to finish your basement walls, meaning covering them permanently with stud walls and sheeting, then it is not always necessary to remove all old existing paint before SANI-TRED installation, as long as good common sense understanding of the importance of the removal of the peeling painted areas are understood and accomplished. It is common to have100% waterproofing success by removing only 50% of the old paint.

You do not need to remove old desktop wallpapers regardless of who created it. If you cannot set a new wallpaper over an existing one then there is something wrong with your system. Request help from a friend or computer professional local to you.