Suction relief valves are mounted as close to the suction mouth of the suction line as is practical. It can be opened manually to allow extra water into the slurry, or automatically if the suction or discharge lines begin to plug, as measured by vacuum and pressure sensors. The suction relief can also be connected to a Production Meter System to help keep at a consistent level of production.

Some valves can be used with vacuum, some cannot. Those that can be will be catalogued with a minimum pressure of 29"Hg. Valves designated in our catalog with a pressure range starting at 0 psi or with a minimum pressure (e.g., 25, 30 or 45 psi) can not be used with vacuum. Valves that can be externally piloted may be used in vacuum applications when properly configured and supplied with external pressure that meets minimum pressure requirement. Not all of our valves are numbered. See similar questions...

No. Feel free to pipe them in either direction. (Please be aware that this is not true with all brands.) See similar questions...

NO. Kitz manufactures standard port ball valves in the end-entry design and full port in a split body design. See similar questions...

Yes, In recovery where calcification occurs the ball valve with its scraper lip design is successful. Wafer-Sphere® in larger lines also is used quite extensively. In addition Metso Automation valves are used in weak and heavy red liquor, magnesium hydroxide slurry, sulfur dioxide in sulfite recovery, feeding spent acid to the evaporators, and in controlling fluids through the slaking tanks. Jamesbury brand ball valves with the proper trims are excellent for chlorine service. See similar questions...

Ball valves typically have higher Cv ratings than globe valves for the same size valve. Therefore the ball valves that are used to handle the same flow as a globe valve will be smaller. The adjusted Cv (Fp factor) must be taken into consideration when sizing valves. This factor takes into account line size when sizing a valve (see page 6 of Engineering, Applications and Installation.) See similar questions...

Pneumadyne valves can be used in water applications. Contact Customer Service for use in potable water applications. See similar questions...

used worldwide, the US based type CGA 540, and the British based type BS # 3. DIN type versions are also being used. See similar questions...

Cv data is noted in each product bulletin. The Cv value represents the flow of water at +60° F (+16° C) through the valve in U.S. gallons per minute, at a pressure drop of 1 psi (0.07 bar). Refer to bulletin T120-1 for a summary of Cv's for all Jamesbury valves. See similar questions...

They are not interchangeable in sizes 1/2"-2". Dimensionally they are different as well as the "union nuts" are of a different thread and will not screw on one another. Sizes 2 1/2"-4" are dimensionally identical and also share the same union nuts,therefore they are interchangeable in those sizes only. See similar questions...

DEI's three way valves are designed for diverting applications. Using them for mixing applications will cause premature wear of the seats and will not produce an equal percentage flow curve. It is DEI's recommendation to pipe the valves for diverting applications only. To use a diverting ball valve for a coil application, simply pipe the valve before the coil (vs. after the coil as you would a mixing application). (See page 10 of Engineering, Applications and Installation.) See similar questions...

YES. All ANSI rated, as well as most threaded, solder joint, and socket weld end valves can be fitted with an Oval Handle (OH) available for sizes ¼²~2². All Carbon and 316SS ball valves comply with NACE MR01-75 as standard. The body bolting for the two piece design is B7M/2HM. See similar questions...

Even though the Z300E type will apparently absorb a great deal more than the 300 ml of O2 they are rated for, the following instructions for use are based on their listed rating. So, when using the Mitsubishi Ageless Z300E oxygen absorption packets, you should allow one packet for every quart and a half (1430 ml) of remaining air volume in your filled storage containers. The FreshPax D750 from the Multisorb Corporation work with just over 3 quarts (2860ml) of remaining air volume. See similar questions...

Two oxygen sensors are used, one for each bank, located between the exhaust manifold and catalytic converters (optional). See similar questions...

Several valve configurations are ideal for use in vacuum applications. Contact our Customer Service department for valve selection. See similar questions...

Flanged floating ball valves are supplied with a locking device that is independent of the operator. They are an integral part of the mechanical stopper. B. The #39 and #49, threaded 2000 WOG SS and Carbon Standard Port, are also provided with Locking Levers as standard. C. #68, Brass 600 WOG Thd. Full Port CGA/AGA/UL/FM rated valve can be provided with a locking lever (LL) or locking Oval Handle (OH-L) as an option. See similar questions...

The Times Square New Year's Eve Ball descends from a flagpole at the top of One Times Square. It can best be seen along Broadway, from 43rd Street to 50th Street, and along Seventh Avenue, as far north as 59th Street. See similar questions...

While you're in the Team Magma/Aqua Secret Base to the east of Lilycove City, you'll need to find a room where there are nine teleport pads. Get the sequence right and continue on, you'll find a set of 4 Item Balls... or are they? Inspecting the two on the right will cause some Electrode to attack. However, the two on the left contain a Nugget and the Master Ball. It is imperative you get it now, otherwise the base will be off limits once you progress too far in the game. See similar questions...

Hyperbaric oxygen treatment may be used to treat a number of clinical conditions. The Undersea and Hyperbaric Medical Society's Oxygen Therapy Committee has recommended hyperbaric oxygen treatment as beneficial in the following clinical conditions including: See similar questions...

There is little evidence to support the use of oxygen cylinders in reducing mortality, however some patients benefit from short bursts from oxygen cylinders PRN especially if evidence of oxygen desaturation on mobilising. Long term survival in patients on LTOT showed that survival improved to 62% at five years. However LTOT should only be initiated after a secondary care review, the criteria is as follows: See similar questions...