No. It is not recommended to use a circular saw to cut pavers. A brick splitter or a high-powered saw with a diamond blade is recommended. These are readily available to rent at Michigan Skid Loader (www.mslinc.com) or other equipment rental stores. For a few cuts, we can cut them for you for a small charge.

Yes, the new V28 Circular Saw uses the same rip fence, 6-1/2" carbide blades and new carrying case as the 18V model. See similar questions...

The Ventmaster can cut through wood framing, sheet metal, asphalt shingles, and green wood. It is even effective on metal roll up doors commonly found on industrial warehouses. It can also cut through car bodies, hoods, and windshields. Yes. Contact Tempest Customer Service at 800-346-2143 for more information on the Ventmaster 375-K rotary cutoff saw. See similar questions...

Endurance® can be cut with most saw types. When using a power miter saw, a high tooth count (80 or more) carbide tip is best. Be sure to have the blade up to speed before beginning your cut. Hack saws and other saw types with metal cutting blades will do the job. See similar questions...

Not yet, but we are working on it. Our system will be able to measure 8 feet to the left and 8 feet to the right. See similar questions...

With the entire V28 program, we wanted all the tools to have corded tool performance. A V28 powered 7-1/4" Circular Saw would have had similar performance to an 18V 6-1/2" Saw which many end-users believe isn't powerful enough for continuous cutting. Keeping the blade size at 6-1/2" allowed us to take the V28 Circular Saw to a new cordless performance level. See similar questions...

No. These machines are for cutting wood products. The only exception is soft aluminium extrusion. This can be cut provided a fine tooth blade (at least 60 tooth) suitable for aluminium is used and the material is securely clamped.Details of blades can be found here. See similar questions...

Plywood, MDF (medium density fiberboard), and Hardboard ? If measured floor-to-ceiling height is 8' or less, subtract 1/2" from the measurement to allow 1/4" expansion clearance top and bottom. Transfer these measurements to panels for cutting. If using a handsaw or table saw, mark and cut the panels face up. If using a portable circular saw or saber saw, mark and cut panels face down. See similar questions...

Answer: When a lane is slip formed, and allowed to cure for a day, a cold joint is formed. This cold construction joint would have tie bars placed into it. Then an adjacent lane is poured up against this new lane. The longitudinal joint will remain tight due to the tie bars. It is anticipated that very little water will penetrate this joint. Therefore, to saw cut the longitudinal joint would be difficult at best and not very beneficial. With a tight cold joint, a sealant would not be needed. See similar questions...

Almost all of our barrels have a bandsaw cut one inch from the muzzle end of the barrel. This indicates that the barrel is not useable beyond that point. When we hand lap our barrels, we do so from each end of the barrel. Because the lapping compound is applied to the lap directly next to the ends, the bore becomes worn slightly oversize. This oversize condition does not extend more than .50"-. See similar questions...

We specialize in manufacturing. They can be laid by any professional paving, tile layer or landscape contractor. Please call us for more information. See similar questions...

Active Directory can record either sequential or circular logs, although sequential is the default and is preferred. Circular logs overwrite transactions at specific intervals, whereas sequential logs are never overwritten (but data in sequential log files whose transactions have been committed to the database are deleted during garbage collection intervals.) Sequential log files are not overwritten with new data. They grow until they reach a specified size. See similar questions...

Of all the cans of worms in motion control, this is one of the wormiest!!! Instead of taking the multiple straight line "almost looks like a circle, but isn't" approach, I wrote the following, which works to the resolution of whatever machine it's on. It functions in much the same manner as the linear interpolation algorithm above in that it involves sequencing an "imaginary" point through space along an arc, and "blips" the axes forward when they need to be to keep up with this point. See similar questions...

Circular breathing allows a player to be able to continually blow air down the didgeridoo without ever stopping for breath. See similar questions...

Yes, kiwis are renowned for their DIY (do it yourself) approach. Please ensure you do your homework first. If in doubt use a professional. See similar questions...

We are building a wonderful display at 114 The Strand Parnell ~ behind the retail stores of French and Pink. You wil have to try the caf? @ Pink while having a leisurely walk through the display. See similar questions...

No. Stoney Ridge pavers are either natural in colour or have an oxide that is mixed through the entire product. This gives the colour more depth and the product a more natural patina which can only improve with age as does natural stone. See similar questions...

No, their surface texture is ideal for obtaining safe traction in pedestrian, vehicular, and pool applications-even when wet. See similar questions...

This will not happen with our installation, since we design a slope that will not allow any standing water to occur. See similar questions...

A 2% pitch (quarter bubble on a level) is more than adequate for your pavers. Pavers should always be pitched to carry water away from structures or poor draining areas. See similar questions...